Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
03-23-2009, 08:00 PM | #1 |
Registered User
Join Date: Oct 2007
Location: Fairfield, PA
Posts: 503
|
WTB Big Block Clutch Pivot Bracket
After doing much research and talking to several people...I found out I need a couple more things to make my swap work...
Clutch Pivot Bracket that goes on side of Big Block for Manual Transmission. This is the piece that bolts with (2) bolts right above the oil filter and I believe it is cast iron??? I also need the bell crank for Big Block only. I am able to fab up what I need but that is my last resort...I would like original stuff if it exist...I hope! |
03-23-2009, 09:01 PM | #2 |
Senior Member
Join Date: Apr 2002
Location: Help! I'm in an office park with its own network of freeways!
Posts: 470
|
Re: WTB Big Block Clutch Pivot Bracket
I have this one:
__________________
'67 C20--427 tall deck/SM420, 4.10 HO52 (Michigan has not been kind to the Old Man) '95 Caprice--355 LT1/T56/3.42 8.5" 10-bolt (daily driver, almost 300k on the chassis) '07 Outback--wife's car. 125k & counting. No head gasket or transmission issues yet. *fingers crossed* |
03-23-2009, 09:23 PM | #3 |
Registered User
Join Date: Oct 2007
Location: Fairfield, PA
Posts: 503
|
Re: WTB Big Block Clutch Pivot Bracket
Pretty sure that's it...Did it come off of a Big Block...? How much would you want for it?
PM me if you want...I'll send you pm with contac information if that will help. Thanks, Alan |
03-23-2009, 10:17 PM | #4 |
Senior Member
Join Date: Apr 2002
Location: Help! I'm in an office park with its own network of freeways!
Posts: 470
|
Re: WTB Big Block Clutch Pivot Bracket
It's a big block pivot. I bought it to use on my engine without realizing the block didn't have the boss above the oil filter.
I don't have a big block bellcrank, no. I reworked my existing small block setup (straight-ish pushrod) instead. I don't have any pics of the mockup on-hand, but tomorrow I could take a few of the bits I did modify. How about $15 shipped?
__________________
'67 C20--427 tall deck/SM420, 4.10 HO52 (Michigan has not been kind to the Old Man) '95 Caprice--355 LT1/T56/3.42 8.5" 10-bolt (daily driver, almost 300k on the chassis) '07 Outback--wife's car. 125k & counting. No head gasket or transmission issues yet. *fingers crossed* Last edited by CE20934; 03-23-2009 at 10:43 PM. Reason: clarity |
03-24-2009, 02:39 AM | #5 |
Senior Member
Join Date: May 2005
Location: hayward, ca
Posts: 268
|
Re: WTB Big Block Clutch Pivot Bracket
aw man. i been looking for onw of these for months! i've seen other people post wanted adds looking for big block clutch linkage and no ever has it. i guess it's just a matter timming when the person who has one just happens to see the ad. yeah, the bracket. good deal too. -jake
__________________
67 short fleet 71 blazer 4x4 72 blazer 2wd 76 gmc sierra 3/4t 4x4 62 bel air 01 blazer extreme member 11,943! |
03-24-2009, 07:35 AM | #6 |
Registered User
Join Date: Oct 2007
Location: Fairfield, PA
Posts: 503
|
Re: WTB Big Block Clutch Pivot Bracket
Sounds good...SOLD...PM your info and I'll get the money headed your way.
Thanks, Alan |
03-24-2009, 05:15 PM | #7 |
Senior Member
Join Date: Apr 2002
Location: Help! I'm in an office park with its own network of freeways!
Posts: 470
|
Re: WTB Big Block Clutch Pivot Bracket
PM sent.
__________________
'67 C20--427 tall deck/SM420, 4.10 HO52 (Michigan has not been kind to the Old Man) '95 Caprice--355 LT1/T56/3.42 8.5" 10-bolt (daily driver, almost 300k on the chassis) '07 Outback--wife's car. 125k & counting. No head gasket or transmission issues yet. *fingers crossed* |
08-18-2009, 10:07 PM | #8 |
Registered User
Join Date: Apr 2003
Location: Maple Grove, MN
Posts: 497
|
Re: WTB Big Block Clutch Pivot Bracket
What a steal, I paid $90 on ebay :*(
|
Bookmarks |
Thread Tools | |
Display Modes | |
|
|