Anybody running LMC's pre-fab exhaust? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Matt72blaze · 03-29-2009, 07:57 PM

Could you snap some pics of it? I'm down to the tail pipes and just can't seem to get them to fit....at least without them hanging about a foot below the frame rails.

Thanks!

Landon · 03-29-2009, 08:49 PM

Your right! The set sucks! Heart throb i presume. It's the same set up as the one from J.C. Whitney so don't try that one either. I had a a heck of a time with it also. I have a 68 4x4 short bed. The right side header pipe wouldn't even fit. I ended up going around the bottom of the trans. case and cross member with 4 ~ 90 deg. bends. I moved the mufflers forward and angled them to achieve the most height for the tail pipes. From there I added 12" straight pipe between the mufflers and the tail pipes. The end result is OK. They aren't a foot low but i'm in the last hole with the clamp that is availabe on the supplied hanger. I'll try to post some pics. for you tomorrow.
Sorry for my rant~
Landon

cdowns · 03-29-2009, 09:45 PM

i've used a couple of the lmc sets never a problem fit good lasted good// hardest thing was figuering what went where

67ChevyRedneck · 03-29-2009, 09:49 PM

It actually hangs pretty low at the rear. I hung my hangers from the bed cross brace just outside of the frame rails. My kit fit fine. It's been on the truck since 2002. And yeah, I was scratching my head for quite a while trying to figure out how it all fit together.

Pics:

Ace in the hole · 03-29-2009, 10:10 PM

I used the LMC set on mine. It does seem to hang a little lower on the back than I would like but it's not that bad.
pics:

Matt72blaze · 03-30-2009, 05:23 PM

thanks a lot guys! this pic answers my questions....i think

i'm pretty sure i have the pieces that run under the carrier bearing and bend up switched because i have the mufflers laying flat right now.

come on 6:30! i'm dying to go fix it!!!

71meangreenc10 · 03-30-2009, 05:31 PM

Got it on my short bed, only had to take one header pipe to midas to get more of an angle put on it, but it works fine.

Smitty

03-29-2009, 07:57 PM	#1
Matt72blaze Registered User Join Date: Sep 2007 Location: Wilmington, OH Posts: 60	Anybody running LMC's pre-fab exhaust? Could you snap some pics of it? I'm down to the tail pipes and just can't seem to get them to fit....at least without them hanging about a foot below the frame rails. Thanks! __________________ 1970 C20 now a K30 1986 3+3 Dually

03-29-2009, 08:49 PM	#2
Landon Registered User Join Date: Feb 2009 Location: Higganum CT Posts: 10	Re: Anybody running LMC's pre-fab exhaust? Your right! The set sucks! Heart throb i presume. It's the same set up as the one from J.C. Whitney so don't try that one either. I had a a heck of a time with it also. I have a 68 4x4 short bed. The right side header pipe wouldn't even fit. I ended up going around the bottom of the trans. case and cross member with 4 ~ 90 deg. bends. I moved the mufflers forward and angled them to achieve the most height for the tail pipes. From there I added 12" straight pipe between the mufflers and the tail pipes. The end result is OK. They aren't a foot low but i'm in the last hole with the clamp that is availabe on the supplied hanger. I'll try to post some pics. for you tomorrow. Sorry for my rant~ Landon

03-29-2009, 09:45 PM	#3
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Anybody running LMC's pre-fab exhaust? i've used a couple of the lmc sets never a problem fit good lasted good// hardest thing was figuering what went where __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

03-29-2009, 09:49 PM	#4
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: Anybody running LMC's pre-fab exhaust? It actually hangs pretty low at the rear. I hung my hangers from the bed cross brace just outside of the frame rails. My kit fit fine. It's been on the truck since 2002. And yeah, I was scratching my head for quite a while trying to figure out how it all fit together. Pics: __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! Last edited by 67ChevyRedneck; 03-29-2009 at 09:55 PM.

03-29-2009, 10:10 PM	#5
Ace in the hole Registered User Join Date: Apr 2007 Location: Kalamazoo, Michigan, USA Posts: 538	Re: Anybody running LMC's pre-fab exhaust? I used the LMC set on mine. It does seem to hang a little lower on the back than I would like but it's not that bad. pics: Attached Images __________________ 1970 K20, 350--- SOLD 05 silverado extended cab short box- duramax Jeep wrangler unlimited

03-30-2009, 05:23 PM	#6
Matt72blaze Registered User Join Date: Sep 2007 Location: Wilmington, OH Posts: 60	Re: Anybody running LMC's pre-fab exhaust? thanks a lot guys! this pic answers my questions....i think i'm pretty sure i have the pieces that run under the carrier bearing and bend up switched because i have the mufflers laying flat right now. come on 6:30! i'm dying to go fix it!!! __________________ 1970 C20 now a K30 1986 3+3 Dually Last edited by Matt72blaze; 03-30-2009 at 05:40 PM.

03-30-2009, 05:31 PM	#7
71meangreenc10 Its a Truck Thing...... Join Date: Dec 2004 Location: Sierra Vista, Arizona Posts: 3,179	Re: Anybody running LMC's pre-fab exhaust? Got it on my short bed, only had to take one header pipe to midas to get more of an angle put on it, but it works fine. Smitty __________________ 71 C10 283/3SPD Full Resto 71 GMC 1500 Sierra Grande http://67-72chevytrucks.com/vboard/s...d.php?t=518599 70 C10 Suburban Former military GSA truck. 72 Chevy Blazer 4X4, Sloppy Jo, Mountain Climber. Wife says no more trucks. http://67-72chevytrucks.com/vboard/s...d.php?t=707378 72 GMC 1 Ton Motor Home, wife said no more trucks until she saw this one. Gen 3 6.0/4L80E 4.10 http://67-72chevytrucks.com/vboard/s...d.php?t=761110 68 GMC Suburban was 3/4 ton, now 1/2.Wife shook her head 71 C30 Wrecker 71 C20 Scott-Bilt As weird as it gets..BB Cheyenne AC Truck 68 GMC Long Stepside. They keep following me home 69 C30 Former Motor Home, Flat Bed time 70 G20 Red-E-Kamp Conversion "I'm your Boogy Van"

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.