Front bumper 72 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

flashed · 11-27-2009, 12:42 AM

Any easy way to remove the 6 original bolts that hold the bumper on. I have sprayed them good with penetrating spray several times .I wish they would just break when I try to loosen them . The first one backed out good til the square part would not hold any more. Any help much appreciated , I will try again tomorrow if I have time.

Strut · 11-27-2009, 01:05 AM

Tighten them back up and take a wire brush over the threads to clean the rust and junk off. A wire wheel on a air tool works the best.

If the bolt turns freely, you can try cutting a slot in the head of the bolt with a cut off wheel (on the outside). Then you can hold it from turning with a flat head screw driver or a flat tip pry bar.... Hope this helps.

71tahoe · 11-27-2009, 11:02 AM

They break better when you tighten the snot out of them. I have loosened them by clamping a steel bar over the head to keep the square part in the slot but it was more trouble than it was worth.

**too much stuff** · 11-27-2009, 11:08 AM

If they are that bad, tighten them till they break...

cdowns · 11-27-2009, 11:15 AM

you can carefully grind the heads off with a small cutoff wheel too

71tahoe · 11-27-2009, 11:21 AM

I'm sure he will have more luck but me, cutoff wheel and careful don't go together.

flashed · 11-27-2009, 11:22 AM

Thanks everyone for the ideas ,I hope to try again in a little while.

CWS · 11-27-2009, 06:35 PM

Last weekend I removed the front bumper from my 67. I have very little experience working on these trucks, so take that into account. I ended up using my grinder with a flap disc (looks like layered sandpaper), to remove the bolt heads. Once I removed about 95% of the head, I hit the bolt with a punch to push it through. A little more grinding, and I was able to punch the bolts through. It took some time, but I did not damage the bumper, and it was a nice day to be outside working on the truck.

Craig

unclewatts · 11-28-2009, 05:08 AM

I just replaced both my front and rear bumpers and were they a PITA. I soaked the nuts with Liquid Wrench overnight, (the liquid not the spray) and got them off with a 3/4 socket and a 2ft. breaker bar. I pushed on the heads to keep them from turning.

flashed · 11-30-2009, 01:38 PM

Got the bumper off , broke 3 off ,ground 1 off and the 2 others came off easy enough after much soaking. Thanks everyone .

flashed · 12-02-2009, 11:56 PM

I just finished installing the front bumper after repainting it. It sure was easier going on than coming off. My budget is low so all Im doing is little things that dont cost anything using stuff I had on the shelf.

OARNGESI · 12-03-2009, 12:03 AM

Any pics of your accomplishment

flashed · 12-03-2009, 11:58 PM

No pictures yet but will try soon.

11-27-2009, 12:42 AM	#1
flashed Registered User Join Date: Oct 2009 Location: canton ga Posts: 12,724	Front bumper 72 Any easy way to remove the 6 original bolts that hold the bumper on. I have sprayed them good with penetrating spray several times .I wish they would just break when I try to loosen them . The first one backed out good til the square part would not hold any more. Any help much appreciated , I will try again tomorrow if I have time.

11-27-2009, 01:05 AM	#2
Strut Registered User Join Date: Oct 2009 Location: Corbin Ky Posts: 247	Re: Front bumper 72 Tighten them back up and take a wire brush over the threads to clean the rust and junk off. A wire wheel on a air tool works the best. If the bolt turns freely, you can try cutting a slot in the head of the bolt with a cut off wheel (on the outside). Then you can hold it from turning with a flat head screw driver or a flat tip pry bar.... Hope this helps. __________________ 1972 Chevy C10 SWB 1999 GMC Sonoma Mini 2008 Yamaha R1 2007 Harley Nightster

11-27-2009, 11:02 AM	#3
71tahoe Registered User Join Date: May 2006 Location: Jonesboro, AR Posts: 916	Re: Front bumper 72 They break better when you tighten the snot out of them. I have loosened them by clamping a steel bar over the head to keep the square part in the slot but it was more trouble than it was worth.

11-27-2009, 11:08 AM	#4
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,787	Re: Front bumper 72 If they are that bad, tighten them till they break... __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

11-27-2009, 11:15 AM	#5
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Front bumper 72 you can carefully grind the heads off with a small cutoff wheel too __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

11-27-2009, 11:21 AM	#6
71tahoe Registered User Join Date: May 2006 Location: Jonesboro, AR Posts: 916	Re: Front bumper 72 I'm sure he will have more luck but me, cutoff wheel and careful don't go together.

11-27-2009, 11:22 AM	#7
flashed Registered User Join Date: Oct 2009 Location: canton ga Posts: 12,724	Re: Front bumper 72 Thanks everyone for the ideas ,I hope to try again in a little while.

11-27-2009, 06:35 PM	#8
CWS Registered User Join Date: Jul 2009 Location: Cary NC Posts: 25	Re: Front bumper 72 Last weekend I removed the front bumper from my 67. I have very little experience working on these trucks, so take that into account. I ended up using my grinder with a flap disc (looks like layered sandpaper), to remove the bolt heads. Once I removed about 95% of the head, I hit the bolt with a punch to push it through. A little more grinding, and I was able to punch the bolts through. It took some time, but I did not damage the bumper, and it was a nice day to be outside working on the truck. Craig

11-28-2009, 05:08 AM	#9
unclewatts 70 Chevrolet=Obsession Join Date: Jun 2009 Location: nice ca Posts: 1,067	Re: Front bumper 72 I just replaced both my front and rear bumpers and were they a PITA. I soaked the nuts with Liquid Wrench overnight, (the liquid not the spray) and got them off with a 3/4 socket and a 2ft. breaker bar. I pushed on the heads to keep them from turning. __________________ I'm Just like my truck. Old, Ugly and Grouchy. Except my truck starts easily in the morning and doesn't smoke! IT'S NOT EASY BEING GREEN! -Kermit the frog 1970 Chevrolet C-10 Longbed Stepside : 350, Muncie M20, 3.08 GM corp. positraction Forest green exterior/light green interior(Where all my money goes) 1996 Toyota Corolla (Parts runner)

11-30-2009, 01:38 PM	#10
flashed Registered User Join Date: Oct 2009 Location: canton ga Posts: 12,724	Re: Front bumper 72 Got the bumper off , broke 3 off ,ground 1 off and the 2 others came off easy enough after much soaking. Thanks everyone .

12-02-2009, 11:56 PM	#11
flashed Registered User Join Date: Oct 2009 Location: canton ga Posts: 12,724	Re: Front bumper 72 I just finished installing the front bumper after repainting it. It sure was easier going on than coming off. My budget is low so all Im doing is little things that dont cost anything using stuff I had on the shelf.

12-03-2009, 12:03 AM	#12
OARNGESI Registered User Join Date: Sep 2008 Location: CASA GRANDE AZ Posts: 4,276	Re: Front bumper 72 Any pics of your accomplishment __________________ 70 SWB STEPSIDE 70 BLAZER 09 challenger

12-03-2009, 11:58 PM	#13
flashed Registered User Join Date: Oct 2009 Location: canton ga Posts: 12,724	Re: Front bumper 72 No pictures yet but will try soon.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.