Gas Tank?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

1971 2wd · 01-26-2003, 09:00 PM

HI EVERYONE,
I HAVE 71 CHEVY 2wd AND I'AM PUTTING A GAS TANK IN IT FROM A 2wd SUBURBAN. HAS ANYONE THERE DONE THIS?? AND DID YOU NEED TO CUT THE REAR BED RAIL FOR CLEARENCE??
THANKS FOR ANY INFO..

*rustedchevy* · 01-26-2003, 09:25 PM

no, dont have to cut frame rails, burb tanks hang down a lil more than blazer tanks,

good luck

short step · 01-27-2003, 08:25 AM

If its a short bed you have to move both of them plus mod the panard rod,just did one and it took a day

1971 2wd · 01-27-2003, 10:51 PM

IT IS A SHORT BED TRUCK, AND THE ONLY PROBLEM I'AM HAVING IS THE CLEARANCE BETWEEN THE TANK AND BEDRAIL ( IT'S THE ONE THAT BOLTS TO THE FRAME).
I WAS LOOKING AT MY 72 BLAZER AND THE TANKS LOOK THE SAME, BUT ON THE BLAZER THE RAIL ABOVE THE TANK IS LOT SHORTER THAN ON THE PICKUP. SO BY NOTCHING IT OUT, I WOULDN'T THINK IT WOULD HURT ANYTHING ( I HOPE ), AND BY DOING IT THAT WAY IT GO RIGHT IN..
THANKS FOR THE INFO, ANY MORE WOULD BE HELPFUL..

justin · 01-27-2003, 11:14 PM

I had to cut out a section of the bed rail for my poly. tank to fit, I surely don't plan on hauling anything heavier than a cooler of ice cold brewskis, so I don't think I should have any problems!
Sorry, that is the one of the only things on my truck I haven't taken a picture of yet!
Break out the old Saw Zaw and don't worry about it!
Good Luck
Justin

01-26-2003, 09:00 PM	#1
1971 2wd Registered User Join Date: Jan 2003 Location: PARADISE,CA Posts: 57	Gas Tank?? HI EVERYONE, I HAVE 71 CHEVY 2wd AND I'AM PUTTING A GAS TANK IN IT FROM A 2wd SUBURBAN. HAS ANYONE THERE DONE THIS?? AND DID YOU NEED TO CUT THE REAR BED RAIL FOR CLEARENCE?? THANKS FOR ANY INFO..

01-27-2003, 11:14 PM	#5
justin PROJECT LO-LYF Join Date: Jul 2002 Location: MO. Posts: 283	I had to cut out a section of the bed rail for my poly. tank to fit, I surely don't plan on hauling anything heavier than a cooler of ice cold brewskis, so I don't think I should have any problems! Sorry, that is the one of the only things on my truck I haven't taken a picture of yet! Break out the old Saw Zaw and don't worry about it! Good Luck Justin __________________ FOUNDING MEMBER OF THE "O-SH*T, THAT TRUCK IS LOW" CLUB PROJECT: LO-LYF Bagged 68 Shorty home.att.net/~justin.lewis

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-26-2003, 09:25 PM	#2
rustedchevy Account Suspended Join Date: Jan 2003 Location: il Posts: 115	no, dont have to cut frame rails, burb tanks hang down a lil more than blazer tanks, good luck

01-27-2003, 08:25 AM	#3
short step Registered User Join Date: Dec 2002 Location: Ludlow,MA Posts: 145	If its a short bed you have to move both of them plus mod the panard rod,just did one and it took a day

01-27-2003, 10:51 PM	#4
1971 2wd Registered User Join Date: Jan 2003 Location: PARADISE,CA Posts: 57	IT IS A SHORT BED TRUCK, AND THE ONLY PROBLEM I'AM HAVING IS THE CLEARANCE BETWEEN THE TANK AND BEDRAIL ( IT'S THE ONE THAT BOLTS TO THE FRAME). I WAS LOOKING AT MY 72 BLAZER AND THE TANKS LOOK THE SAME, BUT ON THE BLAZER THE RAIL ABOVE THE TANK IS LOT SHORTER THAN ON THE PICKUP. SO BY NOTCHING IT OUT, I WOULDN'T THINK IT WOULD HURT ANYTHING ( I HOPE ), AND BY DOING IT THAT WAY IT GO RIGHT IN.. THANKS FOR THE INFO, ANY MORE WOULD BE HELPFUL..



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.