The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-21-2010, 11:58 AM   #1
psychobilly451
Registered User
 
Join Date: Feb 2009
Location: Poughkeepsie NY
Posts: 63
installing CB + antenna and gun rack in a 67 K20?

I plan on installing all these things and dont want to destroy my truck.

I figure I might be able to use some sort of clamps to mount the cb under dash?

I dont want to put any holes in the cab for the antenna. can I mount it on the bed and still get good reception?

does anyone know of a gun rack that wont require me to drill into my cab to mount it?

I guess these aren't necessarily chevy specific but i know you guys care about these trucks like I do.
__________________
1967 K20 Stepside Longbed 250-6 sm420
psychobilly451 is offline   Reply With Quote
Old 03-21-2010, 12:03 PM   #2
mbgmike
Registered User
 
Join Date: Aug 2005
Location: Pasadena,Tx /Pto Pta DR
Posts: 5,415
Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by psychobilly451 View Post
I plan on installing all these things and dont want to destroy my truck.

I figure I might be able to use some sort of clamps to mount the cb under dash?

I dont want to put any holes in the cab for the antenna. can I mount it on the bed and still get good reception?

does anyone know of a gun rack that wont require me to drill into my cab to mount it?

I guess these aren't necessarily chevy specific but i know you guys care about these trucks like I do.
They used to sell the plastic racks for the rear window that clamped on and magnetic CB antennas

I have not seen that in years, not even in texas

Last edited by mbgmike; 03-21-2010 at 12:06 PM.
mbgmike is offline   Reply With Quote
Old 03-21-2010, 12:08 PM   #3
badriv455
'67 Chevy C-50
 
badriv455's Avatar
 
Join Date: Feb 2008
Location: Monticello, IA
Posts: 62
Re: installing CB + antenna and gun rack in a 67 K20?

Dont forget the rebel flag stickers and yosemite sam mudflaps.
__________________
Bad Riv

'67 C50 Flatbed Dump
'98 Z71 Ext. Cab
badriv455 is offline   Reply With Quote
Old 03-21-2010, 12:15 PM   #4
psychobilly451
Registered User
 
Join Date: Feb 2009
Location: Poughkeepsie NY
Posts: 63
Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by badriv455 View Post
Dont forget the rebel flag stickers and yosemite sam mudflaps.
Zombie theme and maybe lady luck mud flap!
__________________
1967 K20 Stepside Longbed 250-6 sm420
psychobilly451 is offline   Reply With Quote
Old 03-21-2010, 12:19 PM   #5
Legolas894
Chemist under the hood...
 
Legolas894's Avatar
 
Join Date: Apr 2009
Location: Fort Erie,ON, Canada
Posts: 617
Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by badriv455 View Post
Dont forget the rebel flag stickers and yosemite sam mudflaps.
X2
__________________


Current fleet:
2013 GMC Sierra, 5.3L, 4x4
1988 GMC Sierra, 305, Auto
1984 Jeep Grand Wagoneer, 360 V8
1997 VW Cabrio, 2.0L
2017 Toyota Rav4, 2.5L

Stuff I wish I still had:
2013 Toyota Matrix [RIP]
1967 GMC 910 Fleetside, 283 V8 [1st Love-SOLD]
1987 Jeep Cherokee Laredo 4X4, 4.0 I-6 [SOLD}
1994 Chevrolet Caprice Classic, 5.7LV8 [SOLD]
1995 Chevrolet Astro AWD, 4.3L V6 (RIP)
1998 Chevrolet Suburban 4x4, 5.7L V8 [SOLD]
Legolas894 is offline   Reply With Quote
Old 03-21-2010, 12:25 PM   #6
mbgmike
Registered User
 
Join Date: Aug 2005
Location: Pasadena,Tx /Pto Pta DR
Posts: 5,415
Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by badriv455 View Post
Dont forget the rebel flag stickers and yosemite sam mudflaps.
Whats wrong with the rebel flag
mbgmike is offline   Reply With Quote
Old 03-21-2010, 12:41 PM   #7
SS68
Registered User
 
SS68's Avatar
 
Join Date: Apr 2008
Location: Dallas, TX
Posts: 126
Re: installing CB + antenna and gun rack in a 67 K20?

at academy they sell the suction cup gun racks, but ive been looking for the old school metal ones my grandpa used to have
SS68 is offline   Reply With Quote
Old 03-21-2010, 01:18 PM   #8
leddzepp
Moderator
 
leddzepp's Avatar
 
Join Date: May 2007
Location: Southern Cal
Posts: 20,022
Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by badriv455 View Post
Dont forget the rebel flag stickers and yosemite sam mudflaps.
true dat
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed.

1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck.


RIP ElJay
RIP 67ChevyRedneck
RIP Grumpy Old Man
RIP FleetsidePaul
leddzepp is offline   Reply With Quote
Old 03-21-2010, 02:45 PM   #9
PanelDeland
I am a Referee of life.
 
PanelDeland's Avatar
 
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
Re: installing CB + antenna and gun rack in a 67 K20?

Look under the dash and you should see the screws that hold the ashtray in place.They may work if you fab or modify the bracket for your CB.The gunrack is a toughy but you may find that the suction cups can be put on an old style rack.The antenna should work fine,you may need a ground.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion.
You can't fix stupid,not even with duct tape.
"My appearance is due to the fact that "GOD" does punish you for having too much fun!"
Barrett-Jackson has perfected alchemy,they make rust into gold!
"You can lead a horse to water but you can't saddle a duck"
"Cleverly disguised as a 'Responsible Adult'
"Sometimes your Knight in shining armor is just a retard in tinfoil"
PanelDeland is offline   Reply With Quote
Old 03-21-2010, 03:49 PM   #10
Shyguy
Junior Member
 
Shyguy's Avatar
 
Join Date: Dec 2006
Location: Southeast Missouri
Posts: 2,436
Thumbs up Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by badriv455 View Post
Dont forget the rebel flag stickers and yosemite sam mudflaps.
Where can I get a set of the "Yosemite Sam" mudflaps?

I already have the gun rack and a line on a big old push bumper.

Danny
__________________
'67 Chevy C-20 short stepper - build complete, 454/SM-465.
'75 C-30 Single Cab DRW-350 small block/NP-435.
'77 GMC-6500 Dump Truck, 427 Tall Deck.
'92 GMC K-3500 Duallie, 454/4L80E.
Shyguy is offline   Reply With Quote
Old 03-21-2010, 04:08 PM   #11
Flat 67
Junior Member
 
Flat 67's Avatar
 
Join Date: Sep 2005
Location: Fresno,California
Posts: 224
Re: installing CB + antenna and gun rack in a 67 K20?

Not knowing if your seat folds forward or not, you can make your own custom gun rack that is seen through the window but attached to the seat. Just a thought................Flat67
Flat 67 is offline   Reply With Quote
Old 03-21-2010, 05:33 PM   #12
vectorit
What?
 
vectorit's Avatar
 
Join Date: Jun 2007
Location: Southern California
Posts: 7,617
Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by Flat 67 View Post
Not knowing if your seat folds forward or not, you can make your own custom gun rack that is seen through the window but attached to the seat. Just a thought................Flat67
I'm more of this thinking.
Since advertising your rifles to the public is usually just asking for issues, so why risk it and figure out a rack idea for behind the seat.

I seem to remember seeing in a catalog like Cabela's, where there was a seat cover that had rifle boots integrated into the back. Something to investigate?
__________________
Chris
1968 K20 Suburban
1972 K10 LWB PU
vectorit is offline   Reply With Quote
Old 03-21-2010, 05:59 PM   #13
psychobilly451
Registered User
 
Join Date: Feb 2009
Location: Poughkeepsie NY
Posts: 63
Re: installing CB + antenna and gun rack in a 67 K20?

thanks guys for a solution to my gun rack. seat covers with a place to put my gun might work.

and i will look to fab something with the ashtray bolts for my cb.
__________________
1967 K20 Stepside Longbed 250-6 sm420
psychobilly451 is offline   Reply With Quote
Old 03-21-2010, 06:25 PM   #14
slomotion
Old Duffer
 
slomotion's Avatar
 
Join Date: Mar 2003
Location: Maine
Posts: 1,822
Re: installing CB + antenna and gun rack in a 67 K20?

I made an "L" bracket and used the top two bolts on the front corner of the box to fasten it to the truck. The antennae mounts to this. The wire runs down and under the cab to come in a hole behind the seat, (fitted with a suitable grommet) then runs under the carpet and up under the dash to the CB.
On my current truck the bracket is fastened to the "headache board" and runs virtually the same way only I came up inside the passenger-side door gasket then under the windshield gasket to the overhead mounted CB.
Both whips were removable from the mounts.
I had a gun rack that had thin ends and was expandable that slipped under the upper and lower rear window gaskets. I used it for my fishing poles, but like vectorit said I don't know if I'd advertise rifles even if the rack would support a couple of them. I know some states requires that hunting firearms must be visible to law enforcement. In our trucks a behind the seat sling wouldn't be visible......tough call.
Don't listen to the rest of these guys rebel flags and Yosemite Sam flaps are not required. I resisted that urge and only use the bullet hole decal in the window
Attached Images
 
__________________
'68 Short C20 Flatbed Dually
w/ 292 4bbl, Langdon cast headers,
and WC T5 trans.

'81 G10 Shorty Van

"Good judgement comes from experience, and a lot of that comes from bad judgement." Will Rogers

"Under promise, then over achieve."
slomotion is offline   Reply With Quote
Old 03-21-2010, 09:17 PM   #15
Legolas894
Chemist under the hood...
 
Legolas894's Avatar
 
Join Date: Apr 2009
Location: Fort Erie,ON, Canada
Posts: 617
Re: installing CB + antenna and gun rack in a 67 K20?

For transmitting, you really want the antenna as high as possible and away from the metal (which is why truckers mount on side mirrors). A rule of thumb was 2/3 of the antenna above the roof line.

I had a magnet mount for the roof but it doesn't look nice. I got it at Radio Shack years ago. It left a mark on the paint when I took it off. There are also 2 in 1 antennas that will do the radio and the CB together. A friend of mine had this and it didn't look too bad and didn't require any drilling for the new hole. It was from Radio Shack as well. That was in the 90s.

I did a quick search and this site has quite a few (including magnet mounts):

http://www.wearecb.com

Good luck.
__________________


Current fleet:
2013 GMC Sierra, 5.3L, 4x4
1988 GMC Sierra, 305, Auto
1984 Jeep Grand Wagoneer, 360 V8
1997 VW Cabrio, 2.0L
2017 Toyota Rav4, 2.5L

Stuff I wish I still had:
2013 Toyota Matrix [RIP]
1967 GMC 910 Fleetside, 283 V8 [1st Love-SOLD]
1987 Jeep Cherokee Laredo 4X4, 4.0 I-6 [SOLD}
1994 Chevrolet Caprice Classic, 5.7LV8 [SOLD]
1995 Chevrolet Astro AWD, 4.3L V6 (RIP)
1998 Chevrolet Suburban 4x4, 5.7L V8 [SOLD]
Legolas894 is offline   Reply With Quote
Old 03-21-2010, 09:59 PM   #16
N2TRUX
Happy to be here
 
N2TRUX's Avatar
 
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,023
Re: installing CB + antenna and gun rack in a 67 K20?

installing CB + antenna and gun rack in my 4 wheel drive..... Isn't that a line from a Hank Jr song?
__________________
Follow me on Facebook and Instagram @N2trux.com

Articles-

"Jake" the 84 to 74 crewcab

"Elwood" the77_Remix

85 GMC Sierra "Scarlett"

"Refining Sierra"
N2TRUX is offline   Reply With Quote
Old 08-26-2010, 11:44 AM   #17
Jblackie47803
Registered User
 
Join Date: Apr 2009
Location: Terre Haute, IN
Posts: 56
Re: installing CB + antenna and gun rack in a 67 K20?

I just installed one in my '67 C-10 but I had to drill holes. They make racks that just clip in on the window seals but I think the small back window precludes us '67 owners from using that kind. By the way, the top shotgun is legal. I've got the Class III paperwork.


Last edited by Jblackie47803; 08-26-2010 at 11:44 AM.
Jblackie47803 is offline   Reply With Quote
Old 08-26-2010, 11:51 AM   #18
marcsRX
68 C10 SWB
 
marcsRX's Avatar
 
Join Date: Nov 2009
Location: Chicago
Posts: 216
Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by jblackie47803 View Post
i just installed one in my '67 c-10 but i had to drill holes. They make racks that just clip in on the window seals but i think the small back window precludes us '67 owners from using that kind. By the way, the top shotgun is legal. I've got the class iii paperwork.

awesome!
__________________
"How much physical pain do you go through on a daily basis that you can directly attribute to your lack of intelligence?" -R0bman
marcsRX is offline   Reply With Quote
Old 08-26-2010, 12:02 PM   #19
ChevLoRay
Old Skool Club
 
ChevLoRay's Avatar
 
Join Date: Jun 2001
Location: Benton, AR "The Heart of Arkansas"
Posts: 10,880
Re: installing CB + antenna and gun rack in a 67 K20?

My cab still has the gun rack, fire extinguisher and cb mike holes.....if the body man hasn't filled 'em. Doubtful he has.

Wanna buy the holes?

Seriously, I put an 8-ft whip on the back bumper "back in the day", but I've also used magnetic base antennae. If you have West Coast or West Coast Jr. mirrors, there should be mounts available at any truck stop. As for the gun mount...I remember seeing a seat cover that had a sleeve in the front of it, behind your legs, for the rifle/shotgun to go. All of this was back in the '70's.
__________________
Member Nr. 2770

'96 GMC Sportside; 4.3/SLT - Daily driven....constantly needs washed.

'69 C-10 SWB; 350/TH400 - in limbo

The older I get, the better I was.

Last edited by ChevLoRay; 08-26-2010 at 12:03 PM.
ChevLoRay is offline   Reply With Quote
Old 08-26-2010, 12:12 PM   #20
68lwb292
Ex-Minitrucker
 
68lwb292's Avatar
 
Join Date: Apr 2009
Location: Bushnell, FL
Posts: 301
Re: installing CB + antenna and gun rack in a 67 K20?

The gun rack my dad used to have slid underneath the rubber at the top and bottom of the window. They had slotted holes with bolts & wing-nuts through them so you wedge them in and tightened the wing nuts and they worked fine. His held a 243 Savage Lever Action and a Browning A-5 Just in case we ran across a Pheasant or a Deer.
68lwb292 is offline   Reply With Quote
Old 08-26-2010, 12:49 PM   #21
slomotion
Old Duffer
 
slomotion's Avatar
 
Join Date: Mar 2003
Location: Maine
Posts: 1,822
Re: installing CB + antenna and gun rack in a 67 K20?

JBlackie, does the rack/rifle barrel bother your shoulder?
__________________
'68 Short C20 Flatbed Dually
w/ 292 4bbl, Langdon cast headers,
and WC T5 trans.

'81 G10 Shorty Van

"Good judgement comes from experience, and a lot of that comes from bad judgement." Will Rogers

"Under promise, then over achieve."
slomotion is offline   Reply With Quote
Old 08-26-2010, 01:10 PM   #22
barryvanhook
Registered User
 
barryvanhook's Avatar
 
Join Date: Feb 2010
Location: Mesa, AZ
Posts: 148
Re: installing CB + antenna and gun rack in a 67 K20?

JBlackie, I'm lovin' your NFA shotgun ... I've got one just like it with the bird's head stock .... ++++1! You may need an AK there also.
__________________
Barry L. Van Hook
'69 Chevy Frankentruck
barryvanhook is offline   Reply With Quote
Old 08-26-2010, 01:31 PM   #23
mrein3
Registered User
 
mrein3's Avatar
 
Join Date: Feb 2000
Location: Center City, MN, USA
Posts: 3,253
Re: installing CB + antenna and gun rack in a 67 K20?

I pulled my gun rack when I brought the truck to MN - the state where nothing is allowed. FWIW, The PO drilled holes to mount the gun rack. In MN all guns must be cased and unloaded so the rack was kinda silly here.

The question I have is why do you want a gun rack? Doesn't that invite somebody to come and steal your weapons? Out of sight is out of mind.
__________________
'70 cab, '71 chassis, 383, TH350, NP205.
'71 Malibu convertible
'72 Malibu hard top
Center City, MN
mrein3 is offline   Reply With Quote
Old 08-26-2010, 02:52 PM   #24
Ronnny
Registered User
 
Join Date: Aug 2010
Location: newnan
Posts: 60
Re: installing CB + antenna and gun rack in a 67 K20?

A gun rack in the window is really for more then just guns. From fishing poles to hanging your hat on. I have also been known to hang my tool belt from it so that it does not slide around in the floor board. but must move it when someone rides with me. If you drill the holes and remove the rack latter you can always plug them with a plastic piece.
Ronnny is offline   Reply With Quote
Old 08-27-2010, 04:28 AM   #25
Jblackie47803
Registered User
 
Join Date: Apr 2009
Location: Terre Haute, IN
Posts: 56
Re: installing CB + antenna and gun rack in a 67 K20?

Quote:
Originally Posted by slomotion View Post
JBlackie, does the rack/rifle barrel bother your shoulder?
The rack itself doesn't seem to. I have to admit I haven't actually drove it with any guns in it yet. My seat is pretty broken down (if my seat cover is any indication) so i sit pretty low too. Being as how my door locks don't work, this will be a seldom used accessory. I will report back after the first time I drive out to the country or the conservation club with artillery.

Last edited by Jblackie47803; 08-27-2010 at 04:31 AM.
Jblackie47803 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:24 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com