looking for pics of fleetsides with bediner - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Piece of Work · 04-13-2010, 07:47 PM

Specifically, where the spray liner ends and the paint begins. I'm looking for ideas on where to mask off.

haysonj · 04-13-2010, 07:55 PM

Quote:

Originally Posted by Piece of Work

Specifically, where the spray liner ends and the paint begins. I'm looking for ideas on where to mask off.

Heres mine its a linex liner and it comes about 3/4 of an inch down the outside.

Cole Trickle · 04-13-2010, 07:56 PM

I have been pondering the same thing because the paint in my bed is flaking.

I think I will tape the top edge of the bedsides so the liner stop at the top of the inner edge. I think the best thing to do on the front is to roll it all the way over the round ledge.

Tail gate I would go as high as needed to match the bedsides.

I will eventually be painting the truck and don't want to do a liner twice.

67chevy2wd · 04-13-2010, 08:03 PM

I plan on putting a steel floor in my 71 and getting it line x'd. I would like to go over the top of the bed rails but I know it is more expensive to go that route. I assume it is more expensive since the masking would take a little more time.

Piece of Work · 04-14-2010, 03:17 PM

haysonj

nice truck! thanks for the pictures.

04-13-2010, 07:47 PM	#1
Piece of Work Cultural Infidel Join Date: Jan 2007 Location: Clearwater, FL Posts: 668	looking for pics of fleetsides with bedliner Specifically, where the spray liner ends and the paint begins. I'm looking for ideas on where to mask off. __________________ posted via La-Z-Boy -Mark 1972 C-10 Fleetside 350/TH350 PS PB A/C Cab Sadly....Sold 1968 Short Fleet 350/TH400 PS PB Delivered by Fine69 Also sadly Sold! It may be that your whole purpose in life is simply to serve as a warning to others. A man is not complete until he is married -- then he is finished. Last edited by Piece of Work; 04-13-2010 at 09:42 PM. Reason: sp.

04-13-2010, 07:56 PM	#3
Cole Trickle C-10 Club Member Join Date: Mar 2010 Location: Corona,CA Posts: 1,001	Re: looking for pics of fleetsides with bediner I have been pondering the same thing because the paint in my bed is flaking. I think I will tape the top edge of the bedsides so the liner stop at the top of the inner edge. I think the best thing to do on the front is to roll it all the way over the round ledge. Tail gate I would go as high as needed to match the bedsides. I will eventually be painting the truck and don't want to do a liner twice.

04-13-2010, 08:03 PM	#4
67chevy2wd Registered User Join Date: Sep 2003 Location: New Salem, ND Posts: 1,558	Re: looking for pics of fleetsides with bediner I plan on putting a steel floor in my 71 and getting it line x'd. I would like to go over the top of the bed rails but I know it is more expensive to go that route. I assume it is more expensive since the masking would take a little more time. __________________ 07 Chevy classic LBZ Duramax (a few mods) '67 Chevy 1/2 ton 2wd (in pieces) '69 Chevy 1/2 ton 2wd (on hold) '71 GMC 3/4 ton 4x4 ‘71 GMC 1/2 ton 2wd suburban

04-14-2010, 03:17 PM	#5
Piece of Work Cultural Infidel Join Date: Jan 2007 Location: Clearwater, FL Posts: 668	Re: looking for pics of fleetsides with bediner haysonj nice truck! thanks for the pictures. __________________ posted via La-Z-Boy -Mark 1972 C-10 Fleetside 350/TH350 PS PB A/C Cab Sadly....Sold 1968 Short Fleet 350/TH400 PS PB Delivered by Fine69 Also sadly Sold! It may be that your whole purpose in life is simply to serve as a warning to others. A man is not complete until he is married -- then he is finished.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.