![]() |
![]() |
#1 |
Registered User
Join Date: Mar 2010
Location: SOCAL
Posts: 19
|
Super T-10 info..??
I'd been doing research in the forums but no luck, can't find useful information at all. What I'd like to know is that is it possible to install one of this transmissions behind an I-6 engine? If so, what parts should i be looking for? Also, what would be better, short or wide ratio, my truck currently has a 4 speed granny-low with 3.07 rear end.
|
![]() |
![]() |
![]() |
#2 | |
just can't cover up my redneck
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
|
Re: Super T-10 info..??
You want the widest ratio you can get, especially because of the 3.07s. You need the lower first gear to get it going. It won't be super low like your granny gear transmission, it's actually a usable gear.
__________________
You can review the site's rules here. Quote:
Bad planning on your part does not necessarily constitute an instant emergency on my part.... The great thing about being a pessimist is that you are either pleasantly surprised or right. ![]() |
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
|
Re: Super T-10 info..??
Any ST-10 for a GM app will bolt to your stock bellhousing. If you get one with a 26 spline input shaft you will need to replace your clutch disc. If your bellhousing is 68 or later you will need a centering ring, which is about a $30 part, or you can make it yourself if you have access to a machine shop. Besides that, you will need to replace or modify your driveshaft if you are replacing a truck type 4 speed.
A wide-ratio version would be the best match for your 3.07 rear. Ray |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Mar 2010
Location: SOCAL
Posts: 19
|
Re: Super T-10 info..??
ok thanks, do you guys know how to identify a wide-ratio ?? Is it by the number of grooves in the input shaft. A 3.42 first gear ratio should be enough right?
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
|
Re: Super T-10 info..??
Yes, count the grooves on the input shaft. A 3.42 ratio will have 6 grooves.
http://www.dandltransmission.com/borgratio.html Ray Last edited by raycow; 09-30-2010 at 04:51 AM. |
![]() |
![]() |
![]() |
#6 | |
"the other guy"
Join Date: Oct 2008
Location: Olivehurst California 95961
Posts: 901
|
Re: Super T-10 info..??
Quote:
__________________
God Said,"Building A 10 Second Import Is Like Coming Out Of The Closet, In The End Ur Still....."EXPLETIVE" ![]() |
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
|
Re: Super T-10 info..??
But does the transmission have a 3.42 1st gear?
Ray |
![]() |
![]() |
![]() |
#8 |
"the other guy"
Join Date: Oct 2008
Location: Olivehurst California 95961
Posts: 901
|
Re: Super T-10 info..??
after seeing this info im not too sure? 6 grooves on input with 27 spline out put? HHHMMMMMMMM?
__________________
God Said,"Building A 10 Second Import Is Like Coming Out Of The Closet, In The End Ur Still....."EXPLETIVE" ![]() |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|