Window rubber DIY - The 1947 - Present Chevrolet & GMC Truck Message Board Network

mdazb · 10-08-2010, 05:31 PM

I'm getting ready to replace the window and vent rubber in my 72 C10. Are there any DIY w/pics? Shortcuts? that you guys can add before I jump into this?

Thanks in advance
Mark

Sammy · 10-08-2010, 09:35 PM

Lots, lots of patience. Do a search for a thread someone just posted some ideas in the last month with pics. Do NOT remove the PIVOT RIVET is my only advise. Everyone I've heard of that removed it was sorry they did.

mdazb · 10-11-2010, 01:34 PM

Thanks for the reply.. I'll do a search to see if I can find it.
Looking for step by step instuctions ( do this first, do this second)..

**LockDoc** · 10-11-2010, 09:47 PM

-
http://67-72chevytrucks.com/vboard/s...ad.php?t=90510

LockDoc

mdazb · 10-12-2010, 12:01 AM

Thanks for the link, Actually I need that info as well. Should've been a little clearer. My bad.
I'm starting the side window channal, vent wing rubber replacement etc. Basically rebuilding the doors. That's the info that's needed now. Still searching posts. Any help would be great.

**NC67Chev** · 10-12-2010, 08:08 AM

Here's a couple of threads for you:

http://67-72chevytrucks.com/vboard/s...t=vent+windows

http://67-72chevytrucks.com/vboard/s...d.php?t=351471

http://67-72chevytrucks.com/vboard/s...d.php?t=153937

I just finished rebuilding a set for my '67, and it really wasn't that bad. I removed the pivot rivet and didn't have any problems getting the new one set. After reading the many threads, the things that I found to help me most are as follows:

1) When removing the vent assembly, remove the rear window track mounting screws. This will allow you to slide the window back, which will make getting the vent assembly out very easy.
2) Get someone that is willing to help you for the process of rebuilding the windows.
3) You must start with the front corner of the vent rubber first. Using dish soap for lube, get the angle portion of the rubber started in the track and sliding it forward seemed to be the easiest way to get the rubber started. Then you can simply use dawn and a flat screwdriver to work the rest into the track.

I think if I rebuild them again, I will try to use pop rivets for everything except the pivot rivet. The biggest thing though is to take your time, do one at a time so you have a reference, don't start into it until you have plenty of time, and walk away for a few minutes if you get frustrated. I hope this helps!

mdazb · 10-12-2010, 10:59 AM

Perfect,, Thanks brother.

project67-stepside · 10-15-2010, 02:04 AM

just did mine with the lmc rubber it was easy, drill out the rivets......

mdazb · 10-19-2010, 05:39 PM

Did you use pop rivets or the LMC rivet kit? I have both, just want to see which is better

10-08-2010, 05:31 PM	#1
mdazb Registered User Join Date: Oct 2004 Location: Nor Cal Posts: 75	Window rubber DIY I'm getting ready to replace the window and vent rubber in my 72 C10. Are there any DIY w/pics? Shortcuts? that you guys can add before I jump into this? Thanks in advance Mark __________________ --------------------------------- 72 C10 SWB 350 Work in progress 98 HD Fatboy 09 HD Heritage Softail 05 Honda Element

10-08-2010, 09:35 PM	#2
Sammy Registered User Join Date: Apr 2000 Location: Bonne Terre, Mo Posts: 3,005	Re: Window rubber DIY Lots, lots of patience. Do a search for a thread someone just posted some ideas in the last month with pics. Do NOT remove the PIVOT RIVET is my only advise. Everyone I've heard of that removed it was sorry they did. __________________ '69 Chevy Long Fleet & '71 GMC Short Step & Project "ODD BALL" "You can wash a pig, soak it in most expensive perfume. In the end it is still just a pig." ODD BALL build thread http://67-72chevytrucks.com/vboard/s...d.php?t=478629"

10-11-2010, 01:34 PM	#3
mdazb Registered User Join Date: Oct 2004 Location: Nor Cal Posts: 75	Re: Window rubber DIY Thanks for the reply.. I'll do a search to see if I can find it. Looking for step by step instuctions ( do this first, do this second).. __________________ --------------------------------- 72 C10 SWB 350 Work in progress 98 HD Fatboy 09 HD Heritage Softail 05 Honda Element

10-11-2010, 09:47 PM	#4
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 26,068	Re: Window rubber DIY - http://67-72chevytrucks.com/vboard/s...ad.php?t=90510 LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

10-12-2010, 12:01 AM	#5
mdazb Registered User Join Date: Oct 2004 Location: Nor Cal Posts: 75	Re: Window rubber DIY Thanks for the link, Actually I need that info as well. Should've been a little clearer. My bad. I'm starting the side window channal, vent wing rubber replacement etc. Basically rebuilding the doors. That's the info that's needed now. Still searching posts. Any help would be great. __________________ --------------------------------- 72 C10 SWB 350 Work in progress 98 HD Fatboy 09 HD Heritage Softail 05 Honda Element

10-12-2010, 08:08 AM	#6
NC67Chev Senior Member Join Date: Oct 2009 Location: Greensboro, NC Posts: 699	Re: Window rubber DIY Here's a couple of threads for you: http://67-72chevytrucks.com/vboard/s...t=vent+windows http://67-72chevytrucks.com/vboard/s...d.php?t=351471 http://67-72chevytrucks.com/vboard/s...d.php?t=153937 I just finished rebuilding a set for my '67, and it really wasn't that bad. I removed the pivot rivet and didn't have any problems getting the new one set. After reading the many threads, the things that I found to help me most are as follows: 1) When removing the vent assembly, remove the rear window track mounting screws. This will allow you to slide the window back, which will make getting the vent assembly out very easy. 2) Get someone that is willing to help you for the process of rebuilding the windows. 3) You must start with the front corner of the vent rubber first. Using dish soap for lube, get the angle portion of the rubber started in the track and sliding it forward seemed to be the easiest way to get the rubber started. Then you can simply use dawn and a flat screwdriver to work the rest into the track. I think if I rebuild them again, I will try to use pop rivets for everything except the pivot rivet. The biggest thing though is to take your time, do one at a time so you have a reference, don't start into it until you have plenty of time, and walk away for a few minutes if you get frustrated. I hope this helps! __________________ 1967 Chevy C-10, 250 L6, Powerglide, 3.73, SWB, Fleetside Upgrades: Power steering, Offset air cleaner, Rear Sport bumper, 3 point safety belts, HEI, -1/-2 springs, 16x5 wheels, McGaughy's disc brake conversion, Sway bar

10-12-2010, 10:59 AM	#7
mdazb Registered User Join Date: Oct 2004 Location: Nor Cal Posts: 75	Re: Window rubber DIY Perfect,, Thanks brother. __________________ --------------------------------- 72 C10 SWB 350 Work in progress 98 HD Fatboy 09 HD Heritage Softail 05 Honda Element

10-15-2010, 02:04 AM	#8
project67-stepside Registered User Join Date: Dec 2009 Location: mesa,az Posts: 94	Re: Window rubber DIY just did mine with the lmc rubber it was easy, drill out the rivets...... __________________ it usual better and faster if u figure it out yourself!!!!

10-19-2010, 05:39 PM	#9
mdazb Registered User Join Date: Oct 2004 Location: Nor Cal Posts: 75	Re: Window rubber DIY Did you use pop rivets or the LMC rivet kit? I have both, just want to see which is better __________________ --------------------------------- 72 C10 SWB 350 Work in progress 98 HD Fatboy 09 HD Heritage Softail 05 Honda Element Last edited by mdazb; 10-19-2010 at 09:19 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.