|
11-16-2010, 04:41 PM
|
#1 |
|
The Red Menace
Join Date: Feb 2009
Location: Roseburg, OR
Posts: 577
|
Bed Swap Pointers?
I'm getting ready to replace the Swiss cheese bed on my truck with a much more solid one. Any advice on getting the old bolts loose? Someone said there are some welds to get through too, where would those be and how hard are they to get through? Any other things I need to be aware of? Thanks!
__________________
1971 Custom 10 - 350/350TH - Pwr steering, gauges, Chrome front bumper, Chrome hubcaps, Door edge guards, HD rear springs (current) 1968 C-20 Custom Camper - 350/350TH (orig 327), Pwr steering & brakes, gauges w/tach (former) 1968 C-20 - 307/3sp column (Dad's when I was a kid) "Driving is like coloring. Things get messy if you can't stay inside the lines." |
|
|
|
11-16-2010, 05:28 PM
|
#2 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: Bed Swap Pointers?
if it's just a matter of swapping beds// there are but a few bolts holding bed onto the frame i normally just grind them down and lift the old bed off and place the new bed in place and use new bolts
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
11-16-2010, 05:59 PM
|
#3 |
|
Registered User
Join Date: Mar 2008
Location: kansas city mo
Posts: 898
|
Re: Bed Swap Pointers?
Yes its just bolts.. You are better off buying new bolts. I just bought some from classic parts for like 10-20 bucks for the set. Just gring them off or cut the bolts.
__________________
Project "Edna Marie"http://www.67-72chevytrucks.com/vboa...74#post5998074 Toys: 2014 Dodge Ram 1967 SHORTBED |
|
|
|
|
11-16-2010, 08:17 PM
|
#4 |
|
Big Red - Now its a SWB!
Join Date: Jun 2009
Location: Oroville, Ca
Posts: 1,624
|
Re: Bed Swap Pointers?
I used a cutting torch to cut the old bolts, then put in a new floor with new bolts.
__________________
68 3/4 ton  (Project)-350 Small Block, .030 over, 10:1 comp, 3998993 heads, C3BX edelbrock intake, comp cams XE268, Holley 670 SA, long tube headers, dual flow 40's, E-fan, Alum rad, currently under the knife getting shortened and bagged  build thread41 3/4 ton (wife's)-flatbed, fully restored to original01 Tahoe LT 4WD (my daily driver)-Magnaflow Muffler, Rollin on 22's 02 Ford Mustang Convertable (Wife's Car)-Flowmaster 50, Clear corners, Intake, sittin on 18's |
|
|
|
|
11-16-2010, 09:41 PM
|
#5 |
|
The Red Menace
Join Date: Feb 2009
Location: Roseburg, OR
Posts: 577
|
Re: Bed Swap Pointers?
Thanks! I bought a new bolt kit for the swap. It'll happen this Saturday. Glad to be finally getting rid of all that rust!
__________________
1971 Custom 10 - 350/350TH - Pwr steering, gauges, Chrome front bumper, Chrome hubcaps, Door edge guards, HD rear springs (current) 1968 C-20 Custom Camper - 350/350TH (orig 327), Pwr steering & brakes, gauges w/tach (former) 1968 C-20 - 307/3sp column (Dad's when I was a kid) "Driving is like coloring. Things get messy if you can't stay inside the lines." |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
