Header clearence w/pics - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Ram-Man · 12-13-2010, 05:59 PM

I put on the Hedman 69640 headers. There is about 3/16" of an inch of clearence at the closet spot on the frame rails. Do you think they will come in contact with the frame under torque? The motor is pretty mild build w/vortec heads on it.

Allensracing · 12-13-2010, 06:07 PM

probably. it depends on how good the rubber in the mounts are

cdowns · 12-13-2010, 06:50 PM

i'd put a torque strap on the driver side to limit torque movement and not worry after that

Allensracing · 12-13-2010, 07:10 PM

that or go ahead and hammer the throttle hard and get it over with

Mike Bradbury · 12-13-2010, 07:47 PM

I had a cheap set of patriot headers on mine and they were about the same distance from the frame and I never had any issues with them comtacting the frame. They were only on for about 6 months before going back to the ram horns because of leaks at the collector.

superchevy · 12-13-2010, 09:24 PM

Break out the die grinder or in my case, the plasma cutter...1/4" plate and boxed the frame...I really wanted to run those Chevelle manifolds, lol....

breezy · 12-13-2010, 10:03 PM

I would not worry about it. If it hits I would say your motor mounts need replaced or you have alot of ponies and very sticky tires. Thanks for posting the pics of that header. I had a post asking if people had used these and didn't get much response. I'm going to get these in the elite series with the ball and socket connector and coated. They look like they fit well to me and the elite have a 3/8 flange at the motor, so shouldn't leak with any luck.Are the plugs easy to get at?

Ram-Man · 12-13-2010, 10:25 PM

Quote:

Originally Posted by breezy

I would not worry about it. If it hits I would say your motor mounts need replaced or you have alot of ponies and very sticky tires. Thanks for posting the pics of that header. I had a post asking if people had used these and didn't get much response. I'm going to get these in the elite series with the ball and socket connector and coated. They look like they fit well to me and the elite have a 3/8 flange at the motor, so shouldn't leak with any luck.Are the plugs easy to get at?

These also have the ball and socket on them but with a 5/16" flange. I may get them jet coated after I break in the motor. #5 cylinder is pretty tight might need shorty plugs I'll see after I get plug wires on.

justincat · 12-13-2010, 11:12 PM

I would be happy if my headers would have fit like that(lol). I would also not worry. If it does hit, all it will do is put a ding in the header, and eventully it wont hit no more. I think that would look better than trying to dent the header or cutting on the frame

12-13-2010, 05:59 PM	#1
Ram-Man Senior Member Join Date: Aug 2006 Location: Minnesota Posts: 943	Header clearence w/pics I put on the Hedman 69640 headers. There is about 3/16" of an inch of clearence at the closet spot on the frame rails. Do you think they will come in contact with the frame under torque? The motor is pretty mild build w/vortec heads on it. Attached Images __________________ Porterbuilt 8 Lugger http://67-72chevytrucks.com/vboard/s...d.php?t=691739

12-13-2010, 06:07 PM	#2
Allensracing Registered User Join Date: Dec 2010 Location: Paradise, ca Posts: 295	Re: Header clearence w/pics probably. it depends on how good the rubber in the mounts are __________________

12-13-2010, 06:50 PM	#3
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Header clearence w/pics i'd put a torque strap on the driver side to limit torque movement and not worry after that __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY Last edited by cdowns; 12-13-2010 at 06:51 PM.

12-13-2010, 07:10 PM	#4
Allensracing Registered User Join Date: Dec 2010 Location: Paradise, ca Posts: 295	Re: Header clearence w/pics that or go ahead and hammer the throttle hard and get it over with __________________

12-13-2010, 09:24 PM	#6
superchevy Got big-block? Join Date: Jul 2000 Location: Austin, Texas Posts: 2,453	Re: Header clearence w/pics Break out the die grinder or in my case, the plasma cutter...1/4" plate and boxed the frame...I really wanted to run those Chevelle manifolds, lol.... Attached Images __________________ '68 CST SWB factory 396/T400 buddy buckets, a/c, ps, pb '72 Corvette convertible 454/4spd/ac, ps, pb '73 GMC Sierra Grande short wide 454/T400 ps, pb, ac '77 K5 Blazer black on red, 350/T350/NP205 ps, pb, ac all original '78 GMC Sierra Classic short wide 454/T400 ps, pb, ac '72 GMC Sprint SP454. 1 of 38 built. '73 GMC Sprint SP454. 1 of 71 built. '75 GMC Sprint SP454. 1 of 25 built. SOLD! '72 GMC K25 4x4 468/4L80e/NP205 build thread http://67-72chevytrucks.com/vboard/s...23#post4324423 SOLD!'55 Chevy gasser 496/4spd build thread http://67-72chevytrucks.com/vboard/s...96#post4324396

12-13-2010, 07:47 PM	#5
Mike Bradbury Registered User Join Date: Apr 2008 Location: San Diego California Posts: 1,316	Re: Header clearence w/pics I had a cheap set of patriot headers on mine and they were about the same distance from the frame and I never had any issues with them comtacting the frame. They were only on for about 6 months before going back to the ram horns because of leaks at the collector. __________________ I'd rather attempt something great and fail.. than try something ordinary and succeed. Norman Vincent Peale Project: Barn Raising http://67-72chevytrucks.com/vboard/s...d.php?t=414961 Project: 30 Be Low https://67-72chevytrucks.com/vboard/...d.php?t=830583

12-13-2010, 10:03 PM	#7
breezy Registered User Join Date: Oct 2010 Location: Palaskifield,Mo. Posts: 71	Re: Header clearence w/pics I would not worry about it. If it hits I would say your motor mounts need replaced or you have alot of ponies and very sticky tires. Thanks for posting the pics of that header. I had a post asking if people had used these and didn't get much response. I'm going to get these in the elite series with the ball and socket connector and coated. They look like they fit well to me and the elite have a 3/8 flange at the motor, so shouldn't leak with any luck.Are the plugs easy to get at? Last edited by breezy; 12-13-2010 at 10:05 PM.

12-13-2010, 11:12 PM	#9
justincat Registered User Join Date: Feb 2010 Location: conway ar Posts: 122	Re: Header clearence w/pics I would be happy if my headers would have fit like that(lol). I would also not worry. If it does hit, all it will do is put a ding in the header, and eventully it wont hit no more. I think that would look better than trying to dent the header or cutting on the frame

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.