IL WTB - Rear frame crossmember 68 GMC leaf spring - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**steinepstein** · 02-20-2011, 12:28 AM

They are not all the same, it should look like this....

**steinepstein** · 02-20-2011, 12:53 AM

I also need the "triangles" that are pictured with the crossmember.

Thanks!

Jon

lynnfield · 02-20-2011, 03:52 AM

I have a 72' GMC that I haven't started parting yet, it should have the piece you need. I'll double check, if it does, $30.00 plus shipping. Greg

**steinepstein** · 02-20-2011, 11:46 AM

Thanks,

If you can send me a pic, I can verify that it fits.

I took my other xmember out and the frame opened up so I need the exact piece...the two lower mounting holes on each side are not directly next to each other, they are slightly offset, you can see in the picture.

Thanks!

**tll74** · 02-20-2011, 01:56 PM

I'll back up lynnfield on this. I have several of these.

**steinepstein** · 02-20-2011, 03:41 PM

Thanks guys, please post some pics if you can.

Jon

lynnfield · 02-20-2011, 08:54 PM

Ok, here's the one I have, straight, some surface rust, couple of nicks. I'm on nights right now on 12hr shifts thru this next week, it would be after that before I could get it pulled for you. If you need it sooner or don't like this one, and have to get it from someone else, no worries, I completely understand. Thanks, Greg

**steinepstein** · 02-21-2011, 07:19 PM

Lynn,

Can you give me the distance of the top two holes on each side (basically the two triangle holes) that mount to the frame, please.

Thanks,

Jon

lynnfield · 02-21-2011, 11:43 PM

Jon, I'll measure and post it tomorrow. Greg

lynnfield · 02-22-2011, 08:42 PM

Jon, here is the space between the top two rivits on the frame. Looks to be about 3 7/8'.

lynnfield · 02-22-2011, 08:46 PM

Jon, here is the spacing between the other two rivits on the top, (one on the frame, one on the cross member). Looks to be close to the same distance.

lynnfield · 02-22-2011, 08:49 PM

Jon distance from side to side from, rivit center to rivit center. Greg

**steinepstein** · 02-22-2011, 10:14 PM

Greg, Awesome, thanks very much. I will check my frame out and get back to you.

Jon

**steinepstein** · 02-26-2011, 03:59 PM

Greg,

I confirmed those measurements, I think that is the one. I will take it, lemme know how you want to be paid.

Thanks,

Jon

lynnfield · 02-27-2011, 03:29 PM

Jon, The shipping will run about $18. If it runs any more than that I'll cover it. So, that will make the total $48. If that's ok with you we can do paypal or money order, your choice. Thanks, Greg

KMC3420 · 07-10-2013, 11:09 AM

Quote:

Originally Posted by tll74

I'll back up lynnfield on this. I have several of these.

I am looking for this exact piece for a 72 frame. I need the cross member plus the triangles, just like in the pictures on this thread. Do you still have one of these available? If so, how much?

lynnfield · 07-10-2013, 12:49 PM

Yes, I have another one.

KMC3420 · 07-10-2013, 03:03 PM

Quote:

Originally Posted by lynnfield

Yes, I have another one.

How much are you asking for it, and what shape is it in?

lynnfield · 07-10-2013, 10:39 PM

$45 shipped since ur a little closer to me. I can get some pics up tomorrow if you need, it's in good shape. Greg

KMC3420 · 07-10-2013, 11:38 PM

Quote:

Originally Posted by lynnfield

$45 shipped since ur a little closer to me. I can get some pics up tomorrow if you need, it's in good shape. Greg

Ill take it for $45. Just pm me on how to pay you and I can send you my address. I have never bought anything on here before but do have a Paypal account.
Posted via Mobile Device

KMC3420 · 07-11-2013, 08:40 AM

Quote:

Originally Posted by lynnfield

$45 shipped since ur a little closer to me. I can get some pics up tomorrow if you need, it's in good shape. Greg

Payment sent via paypal. 7/11/13

lynnfield · 07-11-2013, 04:51 PM

Pics for KMC3420

KMC3420 · 07-11-2013, 05:20 PM

Looks like it will work to me. Thanks for the help. Ill wait to get it in the mail.
Posted via Mobile Device

KMC3420 · 07-11-2013, 05:26 PM

Greg. I was wondering if you might have a driver side lower control arm as well. Mine is bent up. How much if so?
Posted via Mobile Device

02-20-2011, 12:28 AM	#1
steinepstein Senior Member Join Date: Nov 2003 Location: Chicago, IL Posts: 374	WTB - Rear frame crossmember 68 GMC leaf spring They are not all the same, it should look like this.... Attached Images __________________ Project Burro Viejo: http://67-72chevytrucks.com/vboard/s....php?p=3778216

02-20-2011, 12:53 AM	#2
steinepstein Senior Member Join Date: Nov 2003 Location: Chicago, IL Posts: 374	Re: WTB - Rear frame crossmember 68 GMC leaf spring I also need the "triangles" that are pictured with the crossmember. Thanks! Jon __________________ Project Burro Viejo: http://67-72chevytrucks.com/vboard/s....php?p=3778216

02-20-2011, 03:52 AM	#3
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring I have a 72' GMC that I haven't started parting yet, it should have the piece you need. I'll double check, if it does, $30.00 plus shipping. Greg

02-20-2011, 11:46 AM	#4
steinepstein Senior Member Join Date: Nov 2003 Location: Chicago, IL Posts: 374	Re: WTB - Rear frame crossmember 68 GMC leaf spring Thanks, If you can send me a pic, I can verify that it fits. I took my other xmember out and the frame opened up so I need the exact piece...the two lower mounting holes on each side are not directly next to each other, they are slightly offset, you can see in the picture. Thanks! __________________ Project Burro Viejo: http://67-72chevytrucks.com/vboard/s....php?p=3778216

02-20-2011, 01:56 PM	#5
tll74 "Junkyard Dog" Join Date: Jan 2008 Location: Springfield Oregon Posts: 2,527	Re: WTB - Rear frame crossmember 68 GMC leaf spring I'll back up lynnfield on this. I have several of these. __________________ 72 C-10 Cheyenne Super LWB, Vortec 427,TH700, 3.73 posi, tach, tilt, AM-FM,Frame off in process. http://s289.photobucket.com/albums/l...t=7eae161e.pbw 88 Monte Carlo SS bought new only 10k miles. 73 Chevelle SS 454 had since high school. 74 Camaro Z28 350 AT numbers matching, Black on Black. 73 El Camino SS 350 4sp. 70 Chevelle SS 396 4sp, number matching with LS6 454 69 Chevy C30 Car Hauler 86 K20 383 4sp 4" lift frame off restoration. http://s289.photobucket.com/albums/l...t=1b1082d3.pbw

02-20-2011, 03:41 PM	#6
steinepstein Senior Member Join Date: Nov 2003 Location: Chicago, IL Posts: 374	Re: WTB - Rear frame crossmember 68 GMC leaf spring Thanks guys, please post some pics if you can. Jon __________________ Project Burro Viejo: http://67-72chevytrucks.com/vboard/s....php?p=3778216

02-20-2011, 08:54 PM	#7
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring Ok, here's the one I have, straight, some surface rust, couple of nicks. I'm on nights right now on 12hr shifts thru this next week, it would be after that before I could get it pulled for you. If you need it sooner or don't like this one, and have to get it from someone else, no worries, I completely understand. Thanks, Greg Attached Images Last edited by lynnfield; 02-20-2011 at 08:57 PM.

02-21-2011, 07:19 PM	#8
steinepstein Senior Member Join Date: Nov 2003 Location: Chicago, IL Posts: 374	Re: WTB - Rear frame crossmember 68 GMC leaf spring Lynn, Can you give me the distance of the top two holes on each side (basically the two triangle holes) that mount to the frame, please. Thanks, Jon __________________ Project Burro Viejo: http://67-72chevytrucks.com/vboard/s....php?p=3778216

02-21-2011, 11:43 PM	#9
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring Jon, I'll measure and post it tomorrow. Greg

02-22-2011, 08:42 PM	#10
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring Jon, here is the space between the top two rivits on the frame. Looks to be about 3 7/8'. Attached Images

02-22-2011, 08:46 PM	#11
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring Jon, here is the spacing between the other two rivits on the top, (one on the frame, one on the cross member). Looks to be close to the same distance. Attached Images

02-22-2011, 08:49 PM	#12
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring Jon distance from side to side from, rivit center to rivit center. Greg Attached Images

02-22-2011, 10:14 PM	#13
steinepstein Senior Member Join Date: Nov 2003 Location: Chicago, IL Posts: 374	Re: WTB - Rear frame crossmember 68 GMC leaf spring Greg, Awesome, thanks very much. I will check my frame out and get back to you. Jon __________________ Project Burro Viejo: http://67-72chevytrucks.com/vboard/s....php?p=3778216

02-26-2011, 03:59 PM	#14
steinepstein Senior Member Join Date: Nov 2003 Location: Chicago, IL Posts: 374	Re: WTB - Rear frame crossmember 68 GMC leaf spring Greg, I confirmed those measurements, I think that is the one. I will take it, lemme know how you want to be paid. Thanks, Jon __________________ Project Burro Viejo: http://67-72chevytrucks.com/vboard/s....php?p=3778216

02-27-2011, 03:29 PM	#15
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring Jon, The shipping will run about $18. If it runs any more than that I'll cover it. So, that will make the total $48. If that's ok with you we can do paypal or money order, your choice. Thanks, Greg



Register or Log In To remove these advertisements.

07-10-2013, 12:49 PM	#17
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring Yes, I have another one.

07-10-2013, 10:39 PM	#19
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring $45 shipped since ur a little closer to me. I can get some pics up tomorrow if you need, it's in good shape. Greg

07-11-2013, 04:51 PM	#22
lynnfield The Waco Kid Join Date: Oct 2009 Location: Waco, TX. Posts: 1,781	Re: WTB - Rear frame crossmember 68 GMC leaf spring Pics for KMC3420 Attached Images

07-11-2013, 05:20 PM	#23
KMC3420 Registered User Join Date: Dec 2012 Location: Harrison, AR Posts: 1,065	Re: WTB - Rear frame crossmember 68 GMC leaf spring Looks like it will work to me. Thanks for the help. Ill wait to get it in the mail. Posted via Mobile Device __________________ Keagan 68 SWB C-10 original 350 A/C 503 Mean Green

07-11-2013, 05:26 PM	#24
KMC3420 Registered User Join Date: Dec 2012 Location: Harrison, AR Posts: 1,065	Re: WTB - Rear frame crossmember 68 GMC leaf spring Greg. I was wondering if you might have a driver side lower control arm as well. Mine is bent up. How much if so? Posted via Mobile Device __________________ Keagan 68 SWB C-10 original 350 A/C 503 Mean Green

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.