Correct intake for heads - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chukis85c10 · 03-25-2011, 01:49 AM

Hi guys - This is my first time posting here but have been following for quite a bit. I recently started my own project. I have an 85 chevy c10. I am trying to find the correct intake manifold to go with the setup the truck came with. Here are the details for the engine and heads.

Engine - 350 casting #14093638 (86 - 87)
Heads - casting #14102193 (TBI heads)
750 cfm Edlebrock carburetor

This is what came with the truck. It had an old iron intake but its in pretty bad shape. Block is rebuilt and heads have just been refreshed. I've asked around but have gotten different answers as to what intake I should buy. From my research, the heads are for TBI intakes. What would be the correct "carb" intake to go on these heads? Just looking to have a daily driver for now. Maybe a performer intake...? I've seen the answer here before but for the life of me I can't seem to find it. Thanks for your help.

bmchevy1979 · 03-25-2011, 10:21 AM

this is the info I found when I looked up the number it looks like you will need a 87-up non Vortec intake
14102193 305, 350, 87-up

chukis85c10 · 03-26-2011, 01:46 PM

Thanks! This gives me a better idea of what I need to be looking for. I'll post some part # once I find the intake.

chukis85c10 · 04-13-2011, 12:58 AM

I ended up getting the Edelbrock 2104 Performer.

03-25-2011, 10:21 AM	#2
bmchevy1979 Registered User Join Date: Dec 2010 Location: Visalia, Ca Posts: 707	Re: Correct intake for heads this is the info I found when I looked up the number it looks like you will need a 87-up non Vortec intake 14102193 305, 350, 87-up __________________ <Brandon> 1974 Chevrolet K5 Blazer 350sbc/SM465/NP205, dana44 front, corp 14bolt rear with 4.10s and a powertrax locker, custom rear bumper 400sbc in the works. 1981 GMC C1500 stepside 250i6, 3spd, 12bolt with 3.08s 2.5/4drop on 15x10 with 275/50r15 81 GMC C3500 cab-chassis dually with utility bed 350sbc, Sm465, 14bolt with 4.10s nv4500 getting ready to go in 1979 Chevrolet K5 R.I.P. http://67-72chevytrucks.com/vboard/s...d.php?t=434096 1976 Chevrolet C10 R.I.P. http://67-72chevytrucks.com/vboard/s...d.php?t=434195

03-26-2011, 01:46 PM	#3
chukis85c10 Registered User Join Date: Mar 2011 Location: phoenix, az Posts: 8	Re: Correct intake for heads Thanks! This gives me a better idea of what I need to be looking for. I'll post some part # once I find the intake.

04-13-2011, 12:58 AM	#4
chukis85c10 Registered User Join Date: Mar 2011 Location: phoenix, az Posts: 8	Re: Correct intake for heads I ended up getting the Edelbrock 2104 Performer.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-25-2011, 01:49 AM	#1
chukis85c10 Registered User Join Date: Mar 2011 Location: phoenix, az Posts: 8	Correct intake for heads Hi guys - This is my first time posting here but have been following for quite a bit. I recently started my own project. I have an 85 chevy c10. I am trying to find the correct intake manifold to go with the setup the truck came with. Here are the details for the engine and heads. Engine - 350 casting #14093638 (86 - 87) Heads - casting #14102193 (TBI heads) 750 cfm Edlebrock carburetor This is what came with the truck. It had an old iron intake but its in pretty bad shape. Block is rebuilt and heads have just been refreshed. I've asked around but have gotten different answers as to what intake I should buy. From my research, the heads are for TBI intakes. What would be the correct "carb" intake to go on these heads? Just looking to have a daily driver for now. Maybe a performer intake...? I've seen the answer here before but for the life of me I can't seem to find it. Thanks for your help. Last edited by chukis85c10; 03-25-2011 at 01:50 AM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.