sbc motor mounts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

rhuble64 · 05-13-2011, 01:13 AM

putting a 283 in my '63 ish short/step. saw a post from MARKEB01 titled,60-62 gmc to sbc motor and trans mnts. i have the same perches/towers for my truck,but i cant find motor mounts that are "post" style to fit them. anyone know where i may get a set. thanks in advance.

markeb01 · 05-13-2011, 01:16 AM

Is this what you're looking for? O'Reilly Auto part number 2282:

http://www.oreillyauto.com/site/c/de...2327&ppt=C0019

rhuble64 · 05-13-2011, 02:39 AM

not sure. if a bolt goes in the big hole and thru the hole in my perch and it will bolt to my 283 then yes. sure looks like it. will give them a call. thanks for the help. looking forward to exploring this forum,seems like a good find. thanks again ron

markeb01 · 05-13-2011, 02:47 PM

Yes that is how that mount works. The hole in the middle is threaded and the bolt goes through the perch into the center of the rubber area. The item shown was the result of a search for a 1963 Chevy C10 with a 283.

There are several good Chevy truck sites on the web, but this one has the most active membership. It's a friendly place to be if you're looking for input from individuals with a variety of build preferences and specific areas of expertise.

And welcome to the forum!

rhuble64 · 05-13-2011, 08:33 PM

thanks again, was'nt even sure the mounts where available.

**Captainfab** · 05-14-2011, 12:29 AM

Welcome to the forum

The same motor mounts were used for the small block equipped trucks from '63-'72. Don't forget to use a good heavy flat washer on that 7/16" bolt that goes up thru the frame bracket and into the motor mount.

Driveway Dreams · 05-14-2011, 12:32 AM

I gotta get a set too. I just keep forgetting to keep my eyes out.

Really should pay attention so I can work on getting my Burb running before next winter gets here.

karlbenz · 05-15-2011, 07:14 PM

what thread is the 7/16" bolt?

**Captainfab** · 05-16-2011, 01:02 AM

It is 14 thread......7/16"-14 by about 1-1/4 or 1-1/2" long. You'll also need a good heavy flat washer. I would go with a L9 flat washer if you can find a couple.

Quote:

Originally Posted by karlbenz

what thread is the 7/16" bolt?

05-13-2011, 01:13 AM	#1
rhuble64 Registered User Join Date: May 2011 Location: mayfield ny Posts: 5	sbc motor mounts putting a 283 in my '63 ish short/step. saw a post from MARKEB01 titled,60-62 gmc to sbc motor and trans mnts. i have the same perches/towers for my truck,but i cant find motor mounts that are "post" style to fit them. anyone know where i may get a set. thanks in advance.

05-13-2011, 01:16 AM	#2
markeb01 Senior Enthusiast Join Date: Feb 2007 Location: Spokane Valley, WA Posts: 8,356	Re: sbc motor mounts Is this what you're looking for? O'Reilly Auto part number 2282: http://www.oreillyauto.com/site/c/de...2327&ppt=C0019

05-13-2011, 02:39 AM	#3
rhuble64 Registered User Join Date: May 2011 Location: mayfield ny Posts: 5	Re: sbc motor mounts not sure. if a bolt goes in the big hole and thru the hole in my perch and it will bolt to my 283 then yes. sure looks like it. will give them a call. thanks for the help. looking forward to exploring this forum,seems like a good find. thanks again ron

05-13-2011, 02:47 PM	#4
markeb01 Senior Enthusiast Join Date: Feb 2007 Location: Spokane Valley, WA Posts: 8,356	Re: sbc motor mounts Yes that is how that mount works. The hole in the middle is threaded and the bolt goes through the perch into the center of the rubber area. The item shown was the result of a search for a 1963 Chevy C10 with a 283. There are several good Chevy truck sites on the web, but this one has the most active membership. It's a friendly place to be if you're looking for input from individuals with a variety of build preferences and specific areas of expertise. And welcome to the forum! Last edited by markeb01; 05-13-2011 at 02:48 PM.

05-13-2011, 08:33 PM	#5
rhuble64 Registered User Join Date: May 2011 Location: mayfield ny Posts: 5	Re: sbc motor mounts thanks again, was'nt even sure the mounts where available.

05-14-2011, 12:29 AM	#6
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,246	Re: sbc motor mounts Welcome to the forum The same motor mounts were used for the small block equipped trucks from '63-'72. Don't forget to use a good heavy flat washer on that 7/16" bolt that goes up thru the frame bracket and into the motor mount. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE Last edited by Captainfab; 05-14-2011 at 12:31 AM.

05-14-2011, 12:32 AM	#7
Driveway Dreams I have car A.D.D. Join Date: Feb 2009 Location: Greeley, Northern Colorado Posts: 4,147	Re: sbc motor mounts I gotta get a set too. I just keep forgetting to keep my eyes out. Really should pay attention so I can work on getting my Burb running before next winter gets here. __________________ -Gerald Building vehicles in memory of the first "car guy" I ever knew, my Grandpa. Bob Dunham 1935-2009. Rest in peace. 61 GMC Suburban SOLD The 86 build thread SOLD Are you a Colorado member?Click here.

05-15-2011, 07:14 PM	#8
karlbenz Registered User Join Date: Nov 2008 Location: kannapolis, nc Posts: 518	Re: sbc motor mounts what thread is the 7/16" bolt?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.