rebuilding my tailgate inside - out. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

willett · 09-08-2011, 01:13 PM

hey guys,

the tailgate on my truck isn't working so hot anymore and i seem to recall a tutorial somewhere on here about servicing the internals.

trouble is that i can't find it or remember who it was by....

do any of you guys remember?

willett · 09-12-2011, 02:11 PM

anybody?

Rons86 · 09-13-2011, 01:16 PM

Not sure of the thread, but it is fairly easy to take apart. Just be careful not to break the clips that hold the rods to the handle. Easy to scratch the paint also, if you are worried about that. Clean all the parts up, straighten the handle if it is bent (typical problem with these), grease it up good and put it back together.

MalibuSSwagon · 09-13-2011, 11:37 PM

Anyone have any secerts for freeing up a crusty handle? PB blaster worked somewhat the first time I pulled the handle out but i'd like to get it back to almost new quality.

Axle · 09-16-2011, 09:32 PM

Remove it, and clean the rust and paint off the pivot. Douse it with atf, work it until its smooth. If its real bad, toss the handle into a tin of atf and let it soak for a few days, wire brush off the crud, work it, soak it, until your happy with it. Keep well lubed afterward.

Alex.

09-08-2011, 01:13 PM	#1
willett Another Day, Another Dollar Join Date: Nov 2008 Location: North Vancouver, BC Posts: 1,316	rebuilding my tailgate inside - out. hey guys, the tailgate on my truck isn't working so hot anymore and i seem to recall a tutorial somewhere on here about servicing the internals. trouble is that i can't find it or remember who it was by.... do any of you guys remember? __________________ -78 K20 Cheyenne 454 long box, 4" lift, 35" MT's, '84 cab, '80 box "its hip to be square"

09-12-2011, 02:11 PM	#2
willett Another Day, Another Dollar Join Date: Nov 2008 Location: North Vancouver, BC Posts: 1,316	Re: rebuilding my tailgate inside - out. anybody? __________________ -78 K20 Cheyenne 454 long box, 4" lift, 35" MT's, '84 cab, '80 box "its hip to be square"

09-13-2011, 01:16 PM	#3
Rons86 Registered User Join Date: Sep 2008 Location: Holt, Missouri Posts: 94	Re: rebuilding my tailgate inside - out. Not sure of the thread, but it is fairly easy to take apart. Just be careful not to break the clips that hold the rods to the handle. Easy to scratch the paint also, if you are worried about that. Clean all the parts up, straighten the handle if it is bent (typical problem with these), grease it up good and put it back together.

09-13-2011, 11:37 PM	#4
MalibuSSwagon Registered User Join Date: Sep 2009 Location: Weare,NH Posts: 1,592	Re: rebuilding my tailgate inside - out. Anyone have any secerts for freeing up a crusty handle? PB blaster worked somewhat the first time I pulled the handle out but i'd like to get it back to almost new quality. __________________ Eric 1992 Oldsmobile Custom Cruiser 1986 Chevrolet C10\|5.3L\|TKO600\|Shortbed\|Custom Deluxe 1983 Malibu Wagon\|TPI 305\|T5 5 speed\|3.73 non-posi

09-16-2011, 09:32 PM	#5
Axle Registered User Join Date: Jul 2011 Location: SW Ontario Posts: 1,212	Re: rebuilding my tailgate inside - out. Remove it, and clean the rust and paint off the pivot. Douse it with atf, work it until its smooth. If its real bad, toss the handle into a tin of atf and let it soak for a few days, wire brush off the crud, work it, soak it, until your happy with it. Keep well lubed afterward. Alex.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.