The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-21-2012, 09:32 PM   #1
Andyboy
Registered User
 
Andyboy's Avatar
 
Join Date: May 2010
Location: Visalia, CA
Posts: 376
radiator overflowing

Ok I finally took the old girl out. She did great until I got home and shut her off. As soon as I turned her off I heard liquid hitting the ground. I thought it was tranny fluid, but it was coming from the radiator overflow nipple. i don't have an overflow bottle. The truck was sitting for about 5 years. The truck has a v6 305 what should I check first?
Andyboy is offline   Reply With Quote
Old 02-21-2012, 09:39 PM   #2
brokenspoke
Registered User
 
brokenspoke's Avatar
 
Join Date: Jul 2011
Location: Anderson, Texas
Posts: 535
Re: radiator overflowing

Bad radiator cap....
brokenspoke is offline   Reply With Quote
Old 02-21-2012, 10:11 PM   #3
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: radiator overflowing

bad thermostat
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 02-21-2012, 10:26 PM   #4
**grumpy**
Registered User
 
**grumpy**'s Avatar
 
Join Date: Feb 2007
Location: NE Ohio
Posts: 737
Re: radiator overflowing

How much fluid?
had you recently topped it off?
could be just leveling itself off.

Drive again and see if it does it. It may find sweet spot and stop.
If its continues, then Tstat, or cap.
Got a gauge? whats temp read?
__________________
Tim
Road Hounds
**grumpy** is offline   Reply With Quote
Old 02-21-2012, 11:05 PM   #5
Andyboy
Registered User
 
Andyboy's Avatar
 
Join Date: May 2010
Location: Visalia, CA
Posts: 376
Re: radiator overflowing

Hey guys, Yeah I topped it off but left it 1 inch below the top. Cap and thermostat are new. The cap is a 4lbs cap, and the gauge takes along time to read. I went to the gas station and back and it was barely reading above the first line.

What do you guys think about the timing would that effect the temp.?
Andyboy is offline   Reply With Quote
Old 02-21-2012, 11:36 PM   #6
Woogeroo
Registered User
 
Join Date: Aug 2003
Location: tool box
Posts: 3,115
Re: radiator overflowing

crud/debris blocking the air flow across the radiator... either in front or behind. On the grill or on the radiator itself.

does it have a shroud?

since it has been sitting up, check the water pump and see if any coolant is 'weeping' out of the pump at the small little 'weep hole', if so, it needs to be replaced.

does the top hose coming off the thermostat get warm at all? If not hot, the stat may not be opening, even if it is new.

WITH THE ENGINE COLD: you want to have the cap off, crank it up and let it get to operating temp... then watch where the fluid level in the radiator drops to when the thermostat opens... or if it opens at all(keep an eye on the temp. gauge too). If the level does drop have some fresh mixed up coolant to add to top it off. Be sure to put the cap back on snug BEFORE shutting the engine off or it will puke. Good leather work gloves or some thick rags may come in handy. This is the method I use whenever I do work on my radiator/water pump/anything that may have led to a loss of a lot of coolant. That way I know the pump is pulling water through the whole engine.

My pops taught me that one.


-W

p.s. as for an overflow bottle... any kind of container that can handle hot liquid can work.
Woogeroo is offline   Reply With Quote
Old 02-21-2012, 11:51 PM   #7
Andyboy
Registered User
 
Andyboy's Avatar
 
Join Date: May 2010
Location: Visalia, CA
Posts: 376
Re: radiator overflowing

Quote:
Originally Posted by Woogeroo View Post
crud/debris blocking the air flow across the radiator... either in front or behind. On the grill or on the radiator itself.

does it have a shroud?

since it has been sitting up, check the water pump and see if any coolant is 'weeping' out of the pump at the small little 'weep hole', if so, it needs to be replaced.

does the top hose coming off the thermostat get warm at all? If not hot, the stat may not be opening, even if it is new.

WITH THE ENGINE COLD: you want to have the cap off, crank it up and let it get to operating temp... then watch where the fluid level in the radiator drops to when the thermostat opens... or if it opens at all(keep an eye on the temp. gauge too). If the level does drop have some fresh mixed up coolant to add to top it off. Be sure to put the cap back on snug BEFORE shutting the engine off or it will puke. Good leather work gloves or some thick rags may come in handy. This is the method I use whenever I do work on my radiator/water pump/anything that may have led to a loss of a lot of coolant. That way I know the pump is pulling water through the whole engine.

My pops taught me that one.


-W

p.s. as for an overflow bottle... any kind of container that can handle hot liquid can work.


It does not have a shroud. Water pump is new also. I'll have to check the other two things tomorrow. thanks
Andyboy is offline   Reply With Quote
Old 02-22-2012, 12:03 AM   #8
Woogeroo
Registered User
 
Join Date: Aug 2003
Location: tool box
Posts: 3,115
Re: radiator overflowing

Let us know what you find out!

-W
Woogeroo is offline   Reply With Quote
Old 02-22-2012, 07:44 AM   #9
brokenspoke
Registered User
 
brokenspoke's Avatar
 
Join Date: Jul 2011
Location: Anderson, Texas
Posts: 535
Re: radiator overflowing

Quote:
Originally Posted by Andyboy View Post
Hey guys, Yeah I topped it off but left it 1 inch below the top. Cap and thermostat are new. The cap is a 4lbs cap, and the gauge takes along time to read. I went to the gas station and back and it was barely reading above the first line.

What do you guys think about the timing would that effect the temp.?
I may be wrong but a 4 lb cap is not holding enough pressure...imho
brokenspoke is offline   Reply With Quote
Old 02-22-2012, 01:17 PM   #10
Andyboy
Registered User
 
Andyboy's Avatar
 
Join Date: May 2010
Location: Visalia, CA
Posts: 376
Re: radiator overflowing

Well I turned on the truck but with the cap on(forgot to take it off). I had it on for around 15 mins. and it started to shoot out the overflow nipple, constant flow. Turned off engine. Well the upper hose did get warm while the engine was on and the temp gauge went to mid point then dropped alittle. Then it started shooting out. While the engine is running is the water in the radiator flowing or standing still? Mine doesn't flow. I might take the radiator in and have it flushed, it was sitting for around 5 years and summer is around the corner.
Andyboy is offline   Reply With Quote
Old 02-22-2012, 02:38 PM   #11
1963c-10
Registered User
 
1963c-10's Avatar
 
Join Date: Nov 2011
Location: fayetteville nc
Posts: 10,338
Re: radiator overflowing

Might check the heater core also if its runs without a valve.
__________________
1963 Short bed step side SBW 427 big block and borg warner T-16 HD 3 speed manual
http://67-72chevytrucks.com/vboard/s...d.php?t=519869
1963 Short bed fleetside BBW 348 1st gen big block w/Powerglide
http://67-72chevytrucks.com/vboard/s...d.php?t=619024
1964 Short bed trailer
1963c-10 is offline   Reply With Quote
Old 02-22-2012, 05:44 PM   #12
Bears63
...just another truck junkie..
 
Bears63's Avatar
 
Join Date: May 2009
Location: Watertown, SD
Posts: 698
Re: radiator overflowing

Check the radiator cap!!! A 4 lbs cap is nowhere near enough to hold the pressure. It's going to open and there goes your coolant. You should have about a 13 lbs cap on that thing. Try that first.
__________________
Mike "Bear" Shea
Bears63 is offline   Reply With Quote
Old 02-22-2012, 10:30 PM   #13
T Smith
Registered User
 
T Smith's Avatar
 
Join Date: Jan 2011
Location: Vicksburg, Mississippi
Posts: 567
Re: radiator overflowing

It's not going to stay full without a coolant return system, it will find its sweet spot and run an inch or so down, the coolant has to expand and go some where then when it cools it will be low, that's the nature of the beast.
T Smith is offline   Reply With Quote
Old 02-23-2012, 05:01 PM   #14
Andyboy
Registered User
 
Andyboy's Avatar
 
Join Date: May 2010
Location: Visalia, CA
Posts: 376
Re: radiator overflowing

UPDATE: Well I took the radiator to a shop and had them boil it. They said it wasn't plugged up to bad, and had 2 pin holes on top. So I installed the radiator but when I checked the oil, It smells like gas. So the fuel pump will be here tomorrow. I also have to buy a overflow tank and install that, so as soon as I put it back together I'll let you guys know. Thanks for all the feed back.
Andyboy is offline   Reply With Quote
Old 02-23-2012, 06:24 PM   #15
MisterC
Senior Member
 
MisterC's Avatar
 
Join Date: Sep 2011
Location: Hanford, CA
Posts: 1,027
Re: radiator overflowing

Good luck Andy! I don't know anything about those V-6's, but mine was doing the same and I had the guys over at Visalia Radiator go through it. Works like a champ now!
__________________
Poor and content is Rich...and Rich enough! - William Shakespeare
1966 C10 Custom Cab "Luigi"
Big Window - SWB Fleetside
350 V-8 - Powerglide


My not so much a build thread as a "Slow Progression Thread":http://67-72chevytrucks.com/vboard/s...d.php?t=486894
MisterC is offline   Reply With Quote
Old 02-24-2012, 06:53 PM   #16
maxwoof
Registered User
 
Join Date: Mar 2010
Location: Edgewater NJ
Posts: 159
Re: radiator overflowing

As posted earlier, coolant will overflow as it expands when it gets hot. This is magnified after shut down as the heat from the block is absorbed by the coolant which is still. Enough coolant will be forced out of the overflow until ultimately only air is discharged by coolant expansion. In my 62, that puts the level at just above the core. No more drips once this level is reached.
Posted via Mobile Device
maxwoof is offline   Reply With Quote
Old 02-24-2012, 09:25 PM   #17
gimmy 64
Registered User
 
Join Date: Sep 2009
Location: menifee california
Posts: 788
Re: radiator overflowing

i'am not sure if this your problem but alot of people on here are not old enough to remember that before what would you call it --sealed cooling systems it was normal for your car or truck especially if driven on the freeway to puke some coolant on the ground after you stopped engine.that is why alot of guys put catch cans on there cars to not be embarased by your car or truck marking it's spot
gimmy 64 is offline   Reply With Quote
Old 02-28-2012, 10:10 PM   #18
Andyboy
Registered User
 
Andyboy's Avatar
 
Join Date: May 2010
Location: Visalia, CA
Posts: 376
Re: radiator overflowing

Well I got it all put back together and so far so good. I guess the radiator just needed to be cleaned out. Also I'm using a 7lbs. cap and I installed a overflow tank. It didn't puke today so, looks good. Thanks for every ones input.
Andyboy is offline   Reply With Quote
Old 02-28-2012, 10:55 PM   #19
MisterC
Senior Member
 
MisterC's Avatar
 
Join Date: Sep 2011
Location: Hanford, CA
Posts: 1,027
Re: radiator overflowing

Sweet! Glad to hear it.
__________________
Poor and content is Rich...and Rich enough! - William Shakespeare
1966 C10 Custom Cab "Luigi"
Big Window - SWB Fleetside
350 V-8 - Powerglide


My not so much a build thread as a "Slow Progression Thread":http://67-72chevytrucks.com/vboard/s...d.php?t=486894
MisterC is offline   Reply With Quote
Old 02-28-2012, 11:02 PM   #20
64shortbox
Registered User
 
64shortbox's Avatar
 
Join Date: Jan 2011
Location: Tulare, CA
Posts: 734
Re: radiator overflowing

Glad everything worked out OK. What about the fuel smell in the oil? Is that gone now also?
64shortbox is offline   Reply With Quote
Old 02-29-2012, 12:16 AM   #21
chevy_mike
Never Ending Projects
 
chevy_mike's Avatar
 
Join Date: Jul 2006
Location: San Diego, CA
Posts: 3,836
Re: radiator overflowing

My guess is it was the new radiator cap. That extra 3 lbs. can make a big difference. Heck, I didn't even think you could buy one less than 10 lbs. rating.
__________________
.
1965 C10 Panel, Tiki Express http://www.67-72chevytrucks.com/vboa...d.php?t=506580 SOLD
1968 Chevy C10, Long, Fleetside, Hot Rod Hauler http://67-72chevytrucks.com/vboard/s...d.php?t=313233 SOLD
1965 Chevy C10, Long, Fleetside, Hot Rod C10 http://67-72chevytrucks.com/vboard/s...d.php?t=415702 SOLD


We were given two ears and one mouth for a reason... listen twice as much and speak half as often...
chevy_mike is offline   Reply With Quote
Old 02-29-2012, 04:54 PM   #22
Andyboy
Registered User
 
Andyboy's Avatar
 
Join Date: May 2010
Location: Visalia, CA
Posts: 376
Re: radiator overflowing

Quote:
Originally Posted by 64shortbox View Post
Glad everything worked out OK. What about the fuel smell in the oil? Is that gone now also?
Thanks, and yeah I changed the fuel pump and oil and it seems good.
Andyboy is offline   Reply With Quote
Old 02-29-2012, 05:02 PM   #23
MisterC
Senior Member
 
MisterC's Avatar
 
Join Date: Sep 2011
Location: Hanford, CA
Posts: 1,027
Re: radiator overflowing

Quote:
Originally Posted by Andyboy View Post
Thanks, and yeah I changed the fuel pump and oil and it seems good.
Does that mean you're good to drive with me to the CPP gathering on the 16th???

I upgraded my AAA membership so no fears on my part.
__________________
Poor and content is Rich...and Rich enough! - William Shakespeare
1966 C10 Custom Cab "Luigi"
Big Window - SWB Fleetside
350 V-8 - Powerglide


My not so much a build thread as a "Slow Progression Thread":http://67-72chevytrucks.com/vboard/s...d.php?t=486894
MisterC is offline   Reply With Quote
Old 03-02-2012, 12:29 PM   #24
Andyboy
Registered User
 
Andyboy's Avatar
 
Join Date: May 2010
Location: Visalia, CA
Posts: 376
Re: radiator overflowing

Quote:
Originally Posted by MisterC View Post
Does that mean you're good to drive with me to the CPP gathering on the 16th???

I upgraded my AAA membership so no fears on my part.
I wish, I still have to do the brake system. It would be nice.
Andyboy is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:06 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com