65 GMC V6 truck motor questions. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

TERRYP · 05-24-2001, 04:21 PM

My local junk yard just got in a '65 GMC with the stock V6, What's the deal with it? High torque? Worth while? Looks like it runs.

------------------
Everett, Washington
57 3/4 rat, 235, 3spd
66 C-10 Panel, SWB 350 from '68, 3spd, restoring
68 C10 LWB 250 from '66 4spd, dump runner
82 Camaro, 305, THM-200-R4
84 Monte Carlo 305 TH350, land tuna

Ed Cardinal · 01-02-2005, 09:41 AM

Terry, I have a 65 GMC with the 305E V-6 in it and yes they are stump pullers. They are basically more of a dump truck motor then a pickup truck motor. In fact they were put in many dump trucks and big trucks back then. They have a lot of low-end torque for their size and they are actually over-built so they last a long time and will tolerate a lot more then a regular v-6 or v-8 pickup motor. They are not so good on gas and are not so good on a hwy since they are not a high revving motor. But if you plan on using the truck as a truck and not driving it at high speeds for a long time like on a long trip then you cannot go wrong. But they are not as easy to find parts for so keep that in mind..............Ed.

kamikazegmc · 01-02-2005, 10:51 PM

i have 63 w/ 305e v6 it runs real good, it also has about 350k with no rebuild so far. u should check out http://www.6066gmctrucks.org/ it will help u erverything and more.

05-24-2001, 04:21 PM	#1
TERRYP GYRO GEARLOOSE Join Date: Jun 2000 Location: Nevada City, CAEverett, WA Posts: 361	65 GMC V6 truck motor questions. My local junk yard just got in a '65 GMC with the stock V6, What's the deal with it? High torque? Worth while? Looks like it runs. ------------------ Everett, Washington 57 3/4 rat, 235, 3spd 66 C-10 Panel, SWB 350 from '68, 3spd, restoring 68 C10 LWB 250 from '66 4spd, dump runner 82 Camaro, 305, THM-200-R4 84 Monte Carlo 305 TH350, land tuna __________________ Nevada City, CA Everett, Washington 57 3/4 rat, 235, 3spd 66 C-10 Panel, SWB. 350 from '68, 200R4 tranny, 3.07 rear ratio, restoring 68 C10 LWB 350 4spd, 4.56 rear dump runner 82 Camaro, 305, THM-200-R4 84 Monte Carlo 305 TH350, land tuna 85 Tercel SW, snow runner DISGRACED OUTLAW MEMBER OF THE DRUM BRAKE CLUB

01-02-2005, 10:51 PM	#3
kamikazegmc Registered Smarta$$ Join Date: Mar 2004 Location: vancouver, wa Posts: 214	i have 63 w/ 305e v6 it runs real good, it also has about 350k with no rebuild so far. u should check out http://www.6066gmctrucks.org/ it will help u erverything and more. __________________ 63 GMC custom going to be slammed

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-02-2005, 09:41 AM	#2
Ed Cardinal Registered User Join Date: Dec 2004 Posts: 8	Terry, I have a 65 GMC with the 305E V-6 in it and yes they are stump pullers. They are basically more of a dump truck motor then a pickup truck motor. In fact they were put in many dump trucks and big trucks back then. They have a lot of low-end torque for their size and they are actually over-built so they last a long time and will tolerate a lot more then a regular v-6 or v-8 pickup motor. They are not so good on gas and are not so good on a hwy since they are not a high revving motor. But if you plan on using the truck as a truck and not driving it at high speeds for a long time like on a long trip then you cannot go wrong. But they are not as easy to find parts for so keep that in mind..............Ed.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.