could someone please get a measurement for me?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

98layinframe · 06-04-2012, 09:30 AM

Can someone please get a measurement for me? I need to know how wide the front fender wheel lips are apart across the truck from side to side on a 51. ( Im meaning from passenger side width to drivers side.) The suspension setup and wheel combo i currently have place the outside edge of the tire width at 69" total width, and im not sure if i should make wider tubular control arms or even just a simple set of spacers or not.

My trucks toren apart and sitting in my dads warehouse 70 miles away from me.. so i cant measure it myself.

Thanks in advance to anyone that can help!
Posted via Mobile Device

jackson · 06-04-2012, 02:02 PM

Quote:

Originally Posted by 98layinframe

Can someone please get a measurement for me? I need to know how wide the front fender wheel lips are apart across the truck from side to side on a 51. ( Im meaning from passenger side width to drivers side.) The suspension setup and wheel combo i currently have place the outside edge of the tire width at 69" total width, and im not sure if i should make wider tubular control arms or even just a simple set of spacers or not.

My trucks toren apart and sitting in my dads warehouse 70 miles away from me.. so i cant measure it myself.

Thanks in advance to anyone that can help!
Posted via Mobile Device

just measured it . roughly 69 1nches.you will probably need a wheel with not much backspacing

98layinframe · 06-04-2012, 08:36 PM

Thanks man! Guessing thats from inside the lip? The width i had measured earlier was with a 4x4 s10 clip with 2wd wheels on it.

cajundragger · 06-04-2012, 09:02 PM

thumb through this. I'll think you'll find everything you need.

http://www.gmfullsize.com/forum/showthread.php?t=64109

98layinframe · 06-04-2012, 09:33 PM

amazing build... but its not running a s10 clip?

cajundragger · 06-04-2012, 09:43 PM

nope but I know I listed nearly every single measurement you need to lay one of these things out like all the widths and frame heights.

**mr48chev** · 06-04-2012, 10:54 PM

I went out and measured both of my trucks that have fenders on them and got right at 73 inches outside to outside with a 1/2 to 3/4 inch lip inside the fender.

You still have to have room for the front tires to turn without rubbing though.

06-04-2012, 09:30 AM	#1
98layinframe Registered User Join Date: Oct 2011 Location: Pittsburgh Pa Posts: 267	could someone please get a measurement for me?? Can someone please get a measurement for me? I need to know how wide the front fender wheel lips are apart across the truck from side to side on a 51. ( Im meaning from passenger side width to drivers side.) The suspension setup and wheel combo i currently have place the outside edge of the tire width at 69" total width, and im not sure if i should make wider tubular control arms or even just a simple set of spacers or not. My trucks toren apart and sitting in my dads warehouse 70 miles away from me.. so i cant measure it myself. Thanks in advance to anyone that can help! Posted via Mobile Device __________________ 91 s10 - bagged bodydropped 4", 350/700R4, narrowed reared, cantilever rear air bag setup 1951 chevy 3100 - in build/acquiring parts process. Have full C4 Corvette suspension front and rear, tpi 350, 700r4, 18" torque thrust II wheels

06-04-2012, 08:36 PM	#3
98layinframe Registered User Join Date: Oct 2011 Location: Pittsburgh Pa Posts: 267	Re: could someone please get a measurement for me?? Thanks man! Guessing thats from inside the lip? The width i had measured earlier was with a 4x4 s10 clip with 2wd wheels on it. __________________ 91 s10 - bagged bodydropped 4", 350/700R4, narrowed reared, cantilever rear air bag setup 1951 chevy 3100 - in build/acquiring parts process. Have full C4 Corvette suspension front and rear, tpi 350, 700r4, 18" torque thrust II wheels

06-04-2012, 09:02 PM	#4
cajundragger Registered User Join Date: Aug 2006 Location: louisiana Posts: 1,008	Re: could someone please get a measurement for me?? thumb through this. I'll think you'll find everything you need. http://www.gmfullsize.com/forum/showthread.php?t=64109

06-04-2012, 09:33 PM	#5
98layinframe Registered User Join Date: Oct 2011 Location: Pittsburgh Pa Posts: 267	Re: could someone please get a measurement for me?? amazing build... but its not running a s10 clip? __________________ 91 s10 - bagged bodydropped 4", 350/700R4, narrowed reared, cantilever rear air bag setup 1951 chevy 3100 - in build/acquiring parts process. Have full C4 Corvette suspension front and rear, tpi 350, 700r4, 18" torque thrust II wheels

06-04-2012, 09:43 PM	#6
cajundragger Registered User Join Date: Aug 2006 Location: louisiana Posts: 1,008	Re: could someone please get a measurement for me?? nope but I know I listed nearly every single measurement you need to lay one of these things out like all the widths and frame heights.

06-04-2012, 10:54 PM	#7
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,705	Re: could someone please get a measurement for me?? I went out and measured both of my trucks that have fenders on them and got right at 73 inches outside to outside with a 1/2 to 3/4 inch lip inside the fender. You still have to have room for the front tires to turn without rubbing though.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.