K10 motor mount X-member - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**dennislbrooks** · 07-08-2012, 01:04 PM

Can anyone send me a pic of the 1967 or like K10 motor mount x-member? It may be the same for small or big block. I think the 6 cylinder was different. Maybe someone has one laying out. Top and a front side view would be nice. Any extras out there?

74 shortbed 406 · 07-08-2012, 01:06 PM

I believe someone makes them, oru maybe.

BLAZERMAN · 07-08-2012, 01:21 PM

Heres a couple pics of a small block cross member, there were no big blocks from the factory but most guys use this same one when converting, and you are correct the 6 cylinder cross member was different. Should be able to find one off the parts board or DIY4X makes a really nice drop out style with poly bushings.

obijuan · 07-08-2012, 09:00 PM

this is a 292 that i just bought

**dennislbrooks** · 07-12-2012, 08:00 PM

thanks guys, I forgot to check email notification and just thot no one bothered to reply.

Since I did not have one with my 69 rolling chassis, I made one from the top of the 2wd front saddle. I added a little support and it works fine until I dropped the truck 2.5 inches. I used 72 springs and wanted a stock 67 k10 look. Looks good.

So I was wondering if the stock mount had more clearances than mine. It looks like it pushes toward the front some which would benefit me. The tube one I see would work also- maybe even better- if it offsets a little to the front of the diff pumpkin.

I have pics to look at now and will try to fabricate one again.

07-08-2012, 01:04 PM	#1
dennislbrooks Senior Member Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,798	K10 motor mount X-member Can anyone send me a pic of the 1967 or like K10 motor mount x-member? It may be the same for small or big block. I think the 6 cylinder was different. Maybe someone has one laying out. Top and a front side view would be nice. Any extras out there? Last edited by dennislbrooks; 07-08-2012 at 01:08 PM. Reason: more

07-08-2012, 01:06 PM	#2
74 shortbed 406 Registered User Join Date: May 2005 Location: Bowling Green, Mo Posts: 204	Re: K10 motor mount X-member I believe someone makes them, oru maybe. __________________ 1978 GMC K25 2002 Dodge Dakota R/T rc swb In need of some more goodies.

07-08-2012, 01:21 PM	#3
BLAZERMAN Currently Blazerless Join Date: Apr 2000 Location: St. Joseph Mo. Posts: 4,828	Re: K10 motor mount X-member Heres a couple pics of a small block cross member, there were no big blocks from the factory but most guys use this same one when converting, and you are correct the 6 cylinder cross member was different. Should be able to find one off the parts board or DIY4X makes a really nice drop out style with poly bushings. Attached Images __________________ 1972 C/30 133" W.B. C&C 1970 GMC 3500 157" W.B. single wheel C&C

07-08-2012, 09:00 PM	#4
obijuan Registered User Join Date: Jun 2012 Location: cibolo tx Posts: 1,033	Re: K10 motor mount X-member this is a 292 that i just bought

07-12-2012, 08:00 PM	#5
dennislbrooks Senior Member Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,798	Re: K10 motor mount X-member thanks guys, I forgot to check email notification and just thot no one bothered to reply. Since I did not have one with my 69 rolling chassis, I made one from the top of the 2wd front saddle. I added a little support and it works fine until I dropped the truck 2.5 inches. I used 72 springs and wanted a stock 67 k10 look. Looks good. So I was wondering if the stock mount had more clearances than mine. It looks like it pushes toward the front some which would benefit me. The tube one I see would work also- maybe even better- if it offsets a little to the front of the diff pumpkin. I have pics to look at now and will try to fabricate one again.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.