ID driveshaft? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

panhead59 · 11-12-2012, 08:32 AM

Can anyone ID this driveshaft? It looks like a front blazer driveshaft but I have my doubts. It is too long and it looks like it is missing the rear pivot part that would bolt to the transfer case.

**truckster** · 11-12-2012, 10:34 AM

The bottom one in the first picture looks like my Blazer's front shaft. I don't know what the other one is.

Dale99 · 11-12-2012, 11:31 AM

my blazer that has a 203 tc, has a real small dia front shaft. Looks similar to that top one. Have not looked it over for any id marks.

panhead59 · 11-12-2012, 01:41 PM

Yes I know the bottom one is a blazer front drive shaft. I am posting that one just as a comparison to the one in the top of the pic.

**truckster** · 11-12-2012, 02:14 PM

I should have mentioned that mine has the NP205.

panhead59 · 11-15-2012, 10:58 AM

Thanks for the replies. I think I'll put this ? in the suspension thread. Somebody has got to know what this driveshaft fits.

starvinartis · 11-18-2012, 11:44 AM

My 71 Blazer project had 3 of those skinny driveshafts sitting in it when I bought it. Probably a front shaft but different transmission, which could require a longer shaft, or it may be a rear from a say 6 cylinder/3 speed manual trans rig? (light duty)

panhead59 · 11-21-2012, 11:34 AM

I called Spicer (Dana) and they didn't even know. # on driveshaft they said was probably just a casting #. So I'll just give it away like it was given to me. Whoever buys the front one I have for sale can have that one also.

11-12-2012, 08:32 AM	#1
panhead59 Registered User Join Date: Feb 2012 Location: Vinton, Va. Posts: 493	ID driveshaft? Can anyone ID this driveshaft? It looks like a front blazer driveshaft but I have my doubts. It is too long and it looks like it is missing the rear pivot part that would bolt to the transfer case. Attached Images

11-12-2012, 10:34 AM	#2
truckster Senior Member Join Date: Jan 2001 Location: Orem, Utah Posts: 7,922	Re: ID driveshaft? The bottom one in the first picture looks like my Blazer's front shaft. I don't know what the other one is.

11-12-2012, 11:31 AM	#3
Dale99 Registered User Join Date: Nov 2007 Location: NLR, AR Posts: 1,387	Re: ID driveshaft? my blazer that has a 203 tc, has a real small dia front shaft. Looks similar to that top one. Have not looked it over for any id marks.

11-12-2012, 01:41 PM	#4
panhead59 Registered User Join Date: Feb 2012 Location: Vinton, Va. Posts: 493	Re: ID driveshaft? Yes I know the bottom one is a blazer front drive shaft. I am posting that one just as a comparison to the one in the top of the pic.

11-12-2012, 02:14 PM	#5
truckster Senior Member Join Date: Jan 2001 Location: Orem, Utah Posts: 7,922	Re: ID driveshaft? I should have mentioned that mine has the NP205.

11-15-2012, 10:58 AM	#6
panhead59 Registered User Join Date: Feb 2012 Location: Vinton, Va. Posts: 493	Re: ID driveshaft? Thanks for the replies. I think I'll put this ? in the suspension thread. Somebody has got to know what this driveshaft fits.

11-18-2012, 11:44 AM	#7
starvinartis Registered User Join Date: Sep 2009 Location: Phoenix AZ Posts: 105	Re: ID driveshaft? My 71 Blazer project had 3 of those skinny driveshafts sitting in it when I bought it. Probably a front shaft but different transmission, which could require a longer shaft, or it may be a rear from a say 6 cylinder/3 speed manual trans rig? (light duty)

11-21-2012, 11:34 AM	#8
panhead59 Registered User Join Date: Feb 2012 Location: Vinton, Va. Posts: 493	Re: ID driveshaft? I called Spicer (Dana) and they didn't even know. # on driveshaft they said was probably just a casting #. So I'll just give it away like it was given to me. Whoever buys the front one I have for sale can have that one also.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.