Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
02-23-2013, 12:50 AM | #1 |
Active Member
Join Date: Nov 2012
Location: Grand Rapids. MI
Posts: 156
|
Door Handle Escutcheon? Are these for Window Cranks?
Ok sorry this is the third thread about my door panels but I'm a rookie. So my door handle after it eventually get's mounted right, mounts tight with no gap. But my window crank has a large cap. Question is the door escutcheon's used for the window cranks? If so I find two different ones for the door handles. Which one is correct. Different websistes say this one fits up to 72 but some say only 67-71...
http://www.classicindustries.com/tru...ts/cx1508.html Then some websites say this one fits 72-77... http://www.classicparts.com/1972-77-...ctinfo/18-046/ So which one is correct and can I use it for the window crank?
__________________
67 C20 283/4 Speed |
02-23-2013, 12:58 AM | #2 |
Registered User
Join Date: Aug 2009
Location: St. Paul MN.
Posts: 1,996
|
Re: Door Handle Escutcheon? Are these for Window Cranks?
If you have 72 door panels you want the flat ones listed in the classic parts catalog
__________________
Fuzzy |
02-23-2013, 01:00 AM | #3 |
Active Member
Join Date: Nov 2012
Location: Grand Rapids. MI
Posts: 156
|
Re: Door Handle Escutcheon? Are these for Window Cranks?
Ok thanks!!!
Posted via Mobile Device
__________________
67 C20 283/4 Speed |
02-23-2013, 08:06 AM | #4 |
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,858
|
Re: Door Handle Escutcheon? Are these for Window Cranks?
Not sure why the gaps would be different between window winder and door handle. They both take the same eschutcheon in 67-71 or '72.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
02-23-2013, 01:13 PM | #5 | |
Active Member
Join Date: Nov 2012
Location: Grand Rapids. MI
Posts: 156
|
Re: Door Handle Escutcheon? Are these for Window Cranks?
Quote:
Posted via Mobile Device
__________________
67 C20 283/4 Speed |
|
02-23-2013, 03:45 PM | #6 |
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,858
|
Re: Door Handle Escutcheon? Are these for Window Cranks?
All the handles interchange 100%...are the same,except '67s look different. I do wonder if you possibly have a mix between longer '72 shaft and shorter 67-71 shaft on one door. How much is the difference? How far does the one stick out?
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
02-23-2013, 03:50 PM | #7 |
Junior Member
Join Date: Dec 2006
Location: Southeast Missouri
Posts: 2,436
|
Re: Door Handle Escutcheon? Are these for Window Cranks?
My '67 has a longer shaft on the window regulator handle and the door opening handle on the driver's door and we did not notice it until we were putting the handles on. It is just another bit of character my truck has, lol.
__________________
'67 Chevy C-20 short stepper - build complete, 454/SM-465. '75 C-30 Single Cab DRW-350 small block/NP-435. '77 GMC-6500 Dump Truck, 427 Tall Deck. '92 GMC K-3500 Duallie, 454/4L80E. |
02-23-2013, 04:41 PM | #8 |
Active Member
Join Date: Nov 2012
Location: Grand Rapids. MI
Posts: 156
|
Re: Door Handle Escutcheon? Are these for Window Cranks?
Just under a 1/4 inch... That's why I wondering if the correct 72 washer would work.
__________________
67 C20 283/4 Speed |
03-09-2013, 02:39 PM | #9 |
Active Member
Join Date: Nov 2012
Location: Grand Rapids. MI
Posts: 156
|
Re: Door Handle Escutcheon? Are these for Window Cranks?
Ok I got the 72 escutcheons but theres still a 1/4 gap. Anyone use the 67-71 escutcheons on a 72 door panel??
Posted via Mobile Device
__________________
67 C20 283/4 Speed |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|