|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-03-2013, 06:25 AM
|
#1 |
|
Registered User
Join Date: Aug 2012
Location: nantucket,ma
Posts: 230
|
oil pan hitting crossmember
after installing a 509 big block in my 72 c10 2wd i noticed the oil pan just about hitting the front crossmember.i have seen guys notching the crossmember but has anybody shimmed the motor mounts? i just need a quarter inch.i gave up trying to find a different oil pan.thanks
|
|
|
|
03-03-2013, 10:25 AM
|
#2 |
|
Registered User
 
Join Date: Jun 2012
Location: Fitchburg,Mass
Posts: 737
|
Re: oil pan hitting crossmember
What pan are you using???
__________________
62 Willys 4wd Pickup : 72 C-10 swb 504 stroker 09 Taco 3" lift 33" tires: 90 K-5 blazer (plow truck): RIP Ross Little brother
|
|
|
|
|
03-03-2013, 10:32 AM
|
#3 | ||||
|
"I ain't nobody, dork."
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,930
|
Re: oil pan hitting crossmember
Are the motor mounts for a BBC? Are the stands in the correct location?
Gary
__________________
'cuz chicks dig scars... My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread. The Rebuild of Creeping Death after the wreck Quote:
Quote:
Quote:
Quote:
|
||||
|
|
|
|
03-03-2013, 11:23 AM
|
#4 |
|
Registered User
Join Date: Aug 2012
Location: nantucket,ma
Posts: 230
|
Re: oil pan hitting crossmember
my truck is a old drag racing truck it had a 468 cu in motor that was blown up.the oil pan rubbed a little bit with that motor in it.i think it has the original chevy oil pan.not sure on the mounts, good question i will have to find photos of small block and big block mounts/stands and compare.the mounts look factory.thanks for the help i will try to post photos.
|
|
|
|
|
03-03-2013, 11:31 AM
|
#5 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: oil pan hitting crossmember
if it is only a quarter inch or so?? me i would take the torch get the bad area of crossmember cherry red and a nice large hammer and clearance the thing with a nice even relief/// oldschool modification been done like that for as long as i can remember
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
03-03-2013, 11:58 AM
|
#6 | ||||
|
"I ain't nobody, dork."
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,930
|
Re: oil pan hitting crossmember
Nothin' like a torch and a BFH...
 Gary
__________________
'cuz chicks dig scars... My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread. The Rebuild of Creeping Death after the wreck Quote:
Quote:
Quote:
Quote:
|
||||
|
|
|
|
03-03-2013, 05:49 PM
|
#7 |
|
Registered User
Join Date: Aug 2012
Location: nantucket,ma
Posts: 230
|
Re: oil pan hitting crossmember
thanks cdowns i will try and find a photo on a build thread of how close the pan is on other members trucks.
|
|
|
|
|
03-07-2013, 07:48 PM
|
#8 |
|
Registered User
Join Date: Aug 2012
Location: nantucket,ma
Posts: 230
|
Re: oil pan hitting crossmember
thanks GASoline 71 your right the po installed the big block on small block mounts,i did not notice till i saw a thread on the subject and saw the motor sitting up higher than mine.
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
