FL Like new SWB one piece driveshaft

[Hart_Rod]

****SOLD!!****

I'm having a custom built aluminum driveshaft made to install my LS3/6L80E in my 68 SWB, so I'm listing this steel one for sale. I had this driveshaft custom built with all new parts including the yoke, u-joints and tube. It measures 54.5" from center cap to center cap and has has less than 5K miles on it. Asking $175.

R/

[HotRod C/10]

rob what trans were you running? short or long tail?

[Hart_Rod]

Turbo 350, short
Posted via Mobile Device

[lolife99]

Is your old sbc engine stands in the V8 position,... or the 6-cylinder position?

[HotRod C/10]

......according to TCI's website these two trannies are different lengths.
Posted via Mobile Device

[Hart_Rod]

Originally Posted by lolife99

Is your old sbc engine stands in the V8 position,... or the 6-cylinger position?

V6 position

Originally Posted by HotRod C/10

......according to TCI's website these two trannies are different lengths.
Posted via Mobile Device

????

[Hart_Rod]

Here's a picture of the tailshaft.

[HotRod C/10]

Ok I am stabbing my trans tommorrow and will get dims.
Posted via Mobile Device

[Hart_Rod]

Originally Posted by HotRod C/10

Ok I am stabbing my trans tommorrow and will get dims.
Posted via Mobile Device

Sweet! Let me know.
Posted via Mobile Device

[Hart_Rod]

Originally Posted by HotRod C/10

Ok I am stabbing my trans tommorrow and will get dims.
Posted via Mobile Device

What did you figure out?

[Hart_Rod]

bump

[Hart_Rod]

ttt

[Hart_Rod]

bump

[frmula505]

I need one, HotRod C/10 told me about this thread. I had measured mine end to end (i know not as accurate). Anyways mine was 55 1/4 end to end. I need another inch. So it would need to be 56 1/4 end to end. That looks close to what you have. How much shipped to new mexico 87506.

[Hart_Rod]

How about $200 shipped?
Posted via Mobile Device

[frmula505]

Sounds good, you want to do paypal? What is the measurement end to end?

[Hart_Rod]

Originally Posted by frmula505

Sounds good, you want to do paypal? What is the measurement end to end?

Paypal will be good, . I'll measure it for you this afternoon when I get home.

[frmula505]

Thanks

[HotRod C/10]

Hope this works out guys.

[Hart_Rod]

Originally Posted by frmula505

Thanks

Here's a picture with the overall measurement (EDIT from the center of the rear u-joint).

Originally Posted by HotRod C/10

Hope this works out guys.

Thanks for the assist!!

[HotRod C/10]

Its the same length as the one he just gave me..........Bummer

[Hart_Rod]

Originally Posted by HotRod C/10

Its the same length as the one he just gave me..........Bummer

Now I'm confused.
Posted via Mobile Device

[HotRod C/10]

Lol.....I bet.....frmula505 gave me his old drive shaft yesterday same length as yours.........no jokes please
Posted via Mobile Device

[Hart_Rod]

Originally Posted by HotRod C/10

Lol.....I bet.....frmula505 gave me his old drive shaft yesterday same length as yours.........no jokes please
Posted via Mobile Device

Ok, I see what you're saying now. The measurement in the above picture was from the center of the rear u-joint. Here's a picture with the measurement from end to end.

[frmula505]

That should work for me, it will give me close to an inch more center to center of u-joint. Paypal sent. I ran my old driveshaft for a long time, just wasn't going in far enough. This caused a vibration at higher speeds, that got worse as the rear u-joint got bad.