![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
![]() Join Date: Mar 2002
Location: Dallas, TX
Posts: 555
|
Master Cyl to Proportion Valve Tubing
I have a 68 3/4 ton 4x4 that now has a disk brake front end. I am using a 72 master cylinder, proportion valve and brake booster. My question is how should the tubes from the master cylinder to the proportion valve be connected. I have attached two different photos showing the difference.
__________________
1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX |
![]() |
![]() |
![]() |
#2 |
Registered User
![]() Join Date: Dec 2012
Location: Chandler AZ
Posts: 1,149
|
Re: Master Cyl to Proportion Valve Tubing
I just got through with my 3/4 disc conversion and installed the M/C and proportioning valve. According to the instructions I received, it should look like this. Keep in mind this isn't stock and is a disc conversion on a 70.
__________________
1970 Longhorn, Front Disc, 350/4 bolt, 882 heads, HEI, Edelbrock, 700R4, HO-52/4.11. 1996 Corvette, Collector Roadster, LT4, 396, 450RWHP, 6sp, 4.11/Dana44/posi 5 point roll bar And let us not grow weary of doing good, for in due season we will reap, if we do not give up. Gal 6:9 |
![]() |
![]() |
![]() |
#3 |
member #16
![]() Join Date: Dec 1999
Location: Yuba City Ca.
Posts: 3,618
|
Re: Master Cyl to Proportion Valve Tubing
Top pic looks correct for a 3/4 ton, for some reason they were opposite on 1/2 tons. front to front and rear to rear on halfs.
__________________
john http://67-72chevytrucks.com/vboard/showgroups.php board vendors ![]() http://www.flickr.com/photos/1745471...7602865984234/ |
![]() |
![]() |
![]() |
#4 |
Cluster King
![]() Join Date: Nov 2012
Location: Junction City, OR
Posts: 5,263
|
Re: Master Cyl to Proportion Valve Tubing
Here is mine for a 1972 Cheyenne 1/2 ton 2wd.
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jul 2012
Location: Ft Wayne Indiana
Posts: 1,204
|
Re: Master Cyl to Proportion Valve Tubing
Here's my '71 K20
![]()
__________________
71 K20 64 GMC mud truck |
![]() |
![]() |
![]() |
#6 |
Registered User
![]() Join Date: Mar 2002
Location: Dallas, TX
Posts: 555
|
Re: Master Cyl to Proportion Valve Tubing
71K20chevy your setup looks original. Is that the case?
I had ordered new stainless tubes from Inline Tube and they look like yours. I had not seen that configuration before.
__________________
1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jul 2012
Location: Ft Wayne Indiana
Posts: 1,204
|
Re: Master Cyl to Proportion Valve Tubing
Yes they are.
![]()
__________________
71 K20 64 GMC mud truck |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|