vent window question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Thebrownturd · 01-26-2014, 10:25 PM

I would like to hear your guys opinions on the vent window seals. Where can I get some seals that will fit really good and does anyone have any advice to putting in the new felt division bar liner so that it looks good.

PanelDeland · 01-26-2014, 10:36 PM

I can't help on the seals but the division bar was pretty easy to get to look right.I drilled the riverts from the old one.Then I matched the hole to the new one.I had to drill them a slightly larger size because I couldn't find the smaller rivets.I used pop rivets but the anvil of the rivet gun wouldn't fit into the division bar.I cut a short piece of copper tubing and put it over the rod of the rivet then put the rivet into the division bar and got it as tight as I could.Then pumped the handle on the rivet gun.The division bar has stayed put for over ten years.I also recommend using some lube(I use silicone like for foosball bars) on the felt in the channel.It seems to help the felt smooth out and work in.Make sure you have the division bar tight in the channel on every rivet.

Thebrownturd · 01-27-2014, 12:21 AM

Thanks I definitely need to get a rivet gun or something.

70LonghornCST · 01-27-2014, 12:24 AM

I used Precision brand on my rebuild. They worked well.

**leddzepp** · 01-27-2014, 02:27 AM

Quote:

Originally Posted by 70LonghornCST

I used Precision brand on my rebuild. They worked well.

X2. They fit like a glove. GMCPaul and Classicheartbeat carry them.

**leddzepp** · 01-27-2014, 02:33 AM

Quote:

Originally Posted by PanelDeland

I used pop rivets but the anvil of the rivet gun wouldn't fit into the division bar.

I did this as well, except I used a bench grinder to shave down the anvil so it would fit in the channel

PanelDeland · 01-27-2014, 10:51 AM

Also make absolutely sure you have the rivet seated all the way to the bottom of the channel and that the head is flat against the bottom of said channel.

kcsa75 · 01-27-2014, 03:50 PM

Quote:

Originally Posted by leddzepp

X2. They fit like a glove. GMCPaul and Classicheartbeat carry them.

01-26-2014, 10:25 PM	#1
Thebrownturd Registered User Join Date: Jun 2013 Location: Northern Nevada Posts: 233	vent window question I would like to hear your guys opinions on the vent window seals. Where can I get some seals that will fit really good and does anyone have any advice to putting in the new felt division bar liner so that it looks good.

01-26-2014, 10:36 PM	#2
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,992	Re: vent window question I can't help on the seals but the division bar was pretty easy to get to look right.I drilled the riverts from the old one.Then I matched the hole to the new one.I had to drill them a slightly larger size because I couldn't find the smaller rivets.I used pop rivets but the anvil of the rivet gun wouldn't fit into the division bar.I cut a short piece of copper tubing and put it over the rod of the rivet then put the rivet into the division bar and got it as tight as I could.Then pumped the handle on the rivet gun.The division bar has stayed put for over ten years.I also recommend using some lube(I use silicone like for foosball bars) on the felt in the channel.It seems to help the felt smooth out and work in.Make sure you have the division bar tight in the channel on every rivet. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"

01-27-2014, 12:21 AM	#3
Thebrownturd Registered User Join Date: Jun 2013 Location: Northern Nevada Posts: 233	Re: vent window question Thanks I definitely need to get a rivet gun or something.

01-27-2014, 12:24 AM	#4
70LonghornCST Moderator Join Date: Jun 2008 Location: Modesto, CA Posts: 5,775	Re: vent window question I used Precision brand on my rebuild. They worked well. __________________ 2018 Chevy Crew Cab 2006 Impala SS 1965 Plymouth Sport Fury 1970 Chevy Longhorn Bucket Seats Shoulder Belts Front Tow Hooks Factory Air Factory Speedwarning, Tach & Vaccum Factory Tilt CST Package AM/FM Radio Bumper Guards Richard 70 Longhorn CST Build Adding an AM/FM Decal

01-27-2014, 10:51 AM	#7
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,992	Re: vent window question Also make absolutely sure you have the rivet seated all the way to the bottom of the channel and that the head is flat against the bottom of said channel. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.