|
02-23-2014, 08:33 PM
|
#1 |
|
Registered User
Join Date: Feb 2012
Location: Yellowknife, NWT, Canada
Posts: 63
|
Oil pump priming
Alright getting close to starting up my second 5.3. The both engines are from 2007's new body style with AFM. Now this engine has sat on a stand for 3 years.. I would assume that I would need to prime the oil pump like I would on an old sbc? Usually I would have just pulled the dist and put a long common screwdriver down and prime it that way, but with the newer engine obviously doesn't have a dist.. what have you guys done to your engines after they have sat for 3+ years on a stand? obviously don't want to fire it up without seeing oil Px within the first 10 seconds.. suggestions?
|
|
|
|
02-23-2014, 09:09 PM
|
#2 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Re: Oil pump priming
Disable the ign & fuel to the engine, remove the spark plugs....crank the starter 15-20 seconds at a time, until you see pressure @ the guage. After that, plug it all back in, & fire her up? Longhorn
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
02-23-2014, 09:32 PM
|
#3 |
|
Senior Member
 
Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,237
|
Re: Oil pump priming
Your going to have to turn it over cause the oil pump is driven off front the crank
__________________
David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube |
|
|
|
|
02-23-2014, 11:04 PM
|
#4 |
|
meowMEOWmeowMEOW
Join Date: Sep 2009
Location: MKE WI
Posts: 7,128
|
Re: Oil pump priming
There is a tool for this, and you can build one yourself.
Its a force primer, sorta like a reverse brake bleeder, or the lift pumps you would use for lubing a rear end. Ls1tech and youtube have how-to's on making one.
__________________
'66 Short Step / SD Tuned / Big Cam LQ4 / Backhalfed /Built 4l80e / #REBUILDEVERYTHING  |
|
|
|
|
02-27-2014, 11:44 AM
|
#6 | |
|
Registered User
Join Date: Jul 2013
Location: VAFB, CA
Posts: 227
|
Re: Oil pump priming
Quote:
|
|
|
|
|
|
03-02-2014, 08:35 PM
|
#7 |
|
Registered User
Join Date: Apr 2011
Location: Springfield, MO
Posts: 172
|
Re: Oil pump priming
I have done the pull coil wires and plugs crank the key until you get pressure on two different swaps and no problems. I'm not going to lie though, I was nervous both times.
__________________
My 68 Stepper build |
|
|
|
|
03-02-2014, 09:06 PM
|
#8 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Re: Oil pump priming
Not to "muddy the waters here"....I can see the point to do a power prime on that high end engine. On a stocker, that has already run in, I don't see the need to? That roller cam , stock lobes, or mild profiles just wont have any issues that we have seen with the flat tappet hyd grinds? If the bearings are lubbed, you should be good to go
 Longhorn
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
\\ MY YOUTUBE CHANNEL
Linear Mode
