|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
11-02-2014, 11:40 AM
|
#1 |
|
Registered User
Join Date: Nov 2007
Location: Bay Area, Ca
Posts: 2,841
|
Going to pick up another short block
Iron 6.0 turned 408" 6 bolt to work with my heads.
Callies crank and rods Weisco -20cc pistons Essentially my same motor just a 4.03" bore vs a 4.083" bore and a dished piston. This should handle the turbos nicely.
__________________
------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49 |
|
|
|
11-02-2014, 02:10 PM
|
#2 |
|
Registered Truck Offender
Join Date: May 2008
Location: hells training ground (aka Ariz)
Posts: 3,118
|
Re: Going to pick up another short block
i'm jealous. I need to get busy with something,, just not sure what at this point!
__________________
Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral. |
|
|
|
|
11-02-2014, 03:35 PM
|
#3 |
|
Senior Member
Join Date: Apr 2000
Location: Delta,Pa
Posts: 14,948
|
Re: Going to pick up another short block
Sweet. make sure you keep us updated on progress. I need something to tinker with but Im poor. Work has been slow for a while. Anybody wanna donate a truck and engine to me? I will take nice progress pics LOL
__________________
Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member. |
|
|
|
|
11-03-2014, 11:00 PM
|
#4 |
|
Registered User
Join Date: Nov 2007
Location: Bay Area, Ca
Posts: 2,841
|
Re: Going to pick up another short block
I bought it even though I will not use the 6 bolt head set up on it. They welded 1"wide x 1"wide x 2"deep blocks both in the lifter valley and out side of the block. Just not sure I trust it. Plus the ones in the lifter valley are not even tapped.
I will take the motor completely apart to look it over, but I think it was a good buy.
__________________
------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49 |
|
|
|
|
11-03-2014, 11:17 PM
|
#5 | |
|
Senior Member
Join Date: Apr 2000
Location: Delta,Pa
Posts: 14,948
|
Re: Going to pick up another short block
Quote:
__________________
Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member. |
|
|
|
|
|
11-04-2014, 12:56 AM
|
#6 |
|
Registered User
Join Date: Nov 2007
Location: Bay Area, Ca
Posts: 2,841
|
Re: Going to pick up another short block
I will take pics of what I wont use
__________________
------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49 |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
