|
12-05-2014, 09:49 PM
|
#1 |
|
user # 2756
 
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
tranny humps
In the square bodies are the tranny humps bolt in for the manual tranny equipped trucks like the 72 and earlier trucks?
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
12-06-2014, 01:06 PM
|
#2 |
|
Account Suspended
Join Date: Apr 2009
Location: hazard, ky
Posts: 1,674
|
Re: tranny humps
certain years are
|
|
|
|
|
12-06-2014, 10:00 PM
|
#3 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Re: tranny humps
I saw a members build, 1974 I believe, and it had a removable hump. I'm looking to put a SM465 in my 86 K5 and will need the hump removed. I'd rather not drill out the spot welds if I could just cut a hole and then bolt in a tranny cover.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm
|
|
|
|
|
12-06-2014, 11:59 PM
|
#4 |
|
Registered User
Join Date: Jun 2004
Location: El Lago, TX
Posts: 1,668
|
Re: tranny humps
They were bolt in until about 83' / 84'.
|
|
|
|
|
12-07-2014, 12:01 AM
|
#5 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Re: tranny humps
Thanks!
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm
|
|
|
|
|
12-07-2014, 01:38 AM
|
#6 |
|
Junior Member
Join Date: Jun 2004
Location: Murfreesboro, Tn
Posts: 1,092
|
Re: tranny humps
I think there is one in the for sale section.
__________________
1969 impala conv 427 #s loaded. dad bought new 1969 "Judge" RA-3, rare warwick blue/white, #'s 1968 vet convertible #s 427/435 tripower (sold) 1968 belair 2door post #s 427/385 1936 ford 5w coupe dads 1st car 1969 camaro ss (17,xxx) miles Wanted: 69-72 suburban project, 69 camaro convertible. also any big block cars. 69-70 gto judge project. |
|
|
|
|
12-07-2014, 08:05 AM
|
#7 |
|
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Re: tranny humps
My 89 square body had a bolt in too. The answer isn't cut and dry.
__________________
I'm on the Instagram- @Gearhead_Kevin |
|
|
|
|
12-07-2014, 08:19 AM
|
#8 |
|
Registered User
Join Date: Apr 2013
Location: New Brwnswick Canada
Posts: 54
|
Re: tranny humps
I have an '86 4x4 4 speed. the cab was shot. I got another cab witch is still '86 but 2wd. I cut my hump out if my 4x4 ,laid it in the 2wd traced it out and made the new hole 2" smaller and used an insert gun to put threaded inserts in the floor to bolt the hump back in. looks and works good.
|
|
|
|
|
12-07-2014, 11:06 AM
|
#9 | |
|
Account Suspended
Join Date: Apr 2009
Location: hazard, ky
Posts: 1,674
|
Re: tranny humps
Quote:
|
|
|
|
|
|
12-07-2014, 11:17 AM
|
#10 |
|
Account Suspended
Join Date: Jun 2011
Location: Des Moines, IA.
Posts: 4,143
|
Re: tranny humps
I've always seen bolt in ones-I have an extra one in nice shape if you need one. The tool used to install the riv-nuts is called a riv-gun and you can buy different sizes of riv-nuts. After drilling the holes as Jeff said, installing them is a breeze.
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
