The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-10-2015, 07:55 PM   #1
UNHLAW2016
Registered User
 
Join Date: May 2015
Location: Dover, NH
Posts: 35
Square Steel Stock on a 3/4 Ton Frame--Why?

Good evening,
I have one that to me appears perplexing. I bought an all original 79 k20 with 25,000 mi from the fire company over the winter. I am just getting around to starting on it. From about where the frame turns up behind the cab to the beginning of the forward most rear spring hanger there appears to be a piece of I dont know 1 1/2" (The thickness of the width of the frame) square stock welded to both sides of the frame. Other than this the frame is mint, no damage, no repairs, no replaced rivets.
Any ideas?
UNHLAW2016 is offline   Reply With Quote
Old 06-10-2015, 08:49 PM   #2
nonstop
Registered User
 
Join Date: Dec 2014
Location: Northern California
Posts: 422
Re: Square Steel Stock on a 3/4 Ton Frame--Why?

My guess would be it was some type of reinforcement for fire apparatus.
nonstop is offline   Reply With Quote
Old 06-10-2015, 11:35 PM   #3
greg64
Registered User
 
greg64's Avatar
 
Join Date: Dec 2007
Location: Kimberley, BC, Canada
Posts: 799
Re: Square Steel Stock on a 3/4 Ton Frame--Why?

I'm thinking, as above, that maybe it was mounting fire equipment, not specifically to strengthen the frame. Any holes in the steel that was added?
__________________
Greg
64 GMC Suburban - 283, NV3500, 14 bolt
77 C10 swb - 292, SM465, 12 bolt
greg64 is offline   Reply With Quote
Old 06-10-2015, 11:43 PM   #4
UNHLAW2016
Registered User
 
Join Date: May 2015
Location: Dover, NH
Posts: 35
Re: Square Steel Stock on a 3/4 Ton Frame--Why?

No, it is the weirdest thing.
The utility body on the truck now does not appear to be 35 years old. I am wondering if it was for U bolts maybe?
The frame looks spotless, there and everywhere
There was a pump apparatus in the back before I bought it!
UNHLAW2016 is offline   Reply With Quote
Old 06-10-2015, 11:56 PM   #5
Richs'55
Registered User
 
Join Date: Aug 2014
Location: Fort Dodge, Iowa
Posts: 120
Re: Square Steel Stock on a 3/4 Ton Frame--Why?

Retired Firefighter. When I started on the job in 1983, we had a 1978 K20 with a pump/utility body. Nice little truck for putting out grass fires and small car fires.
It had the pump mounted right behind the cab. Power take off from the transmission would have been right ahead of that.

Suppose would need room to connect to pump and lots of fittings going in and out of that area. Along with a needing access to work on pump/fittings from below.

Post up a picture of the whole truck if you can.
Richs'55 is offline   Reply With Quote
Old 06-10-2015, 11:58 PM   #6
Richs'55
Registered User
 
Join Date: Aug 2014
Location: Fort Dodge, Iowa
Posts: 120
Re: Square Steel Stock on a 3/4 Ton Frame--Why?

Oh, also those 25,000 miles. Fire trucks are really clean because they are maintained /cleaned every day. But that engine, has probably twice as many hours than miles.
They sit a lot while pumping.
Richs'55 is offline   Reply With Quote
Old 06-11-2015, 09:31 PM   #7
Pine Bark Auto
Registered User
 
Join Date: Dec 2008
Location: Clover, SC
Posts: 55
Re: Square Steel Stock on a 3/4 Ton Frame--Why?

Around here, the volunteer Fire Depts used 3/4 ton trucks as "Brush Trucks". They had a small tank mounted in the bed with a pump for fighting small brush fires. I know of 2 that sustained severe frame damage due to crossing terraces and ditches with too much speed and full tanks of water. I bet many others suffered the same damage and word got around to beef up the frames. Chip.
Pine Bark Auto is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:53 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com