|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-29-2015, 05:33 PM
|
#1 |
|
Registered User
Join Date: Jul 2014
Location: Phoenix
Posts: 114
|
Anyone know how to remove this?
I know you remove the bolt, but I'm Having a very hard time removing this piece.
http://67-72chevytrucks.com/vboard/a...1&d=1443562280 |
|
|
|
09-29-2015, 05:38 PM
|
#2 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: Anyone know how to remove this?
are you reusing the wiring harness?
They plug into each other (inside and outside) so they are probably stuck from years of corrosion. Should be able to wiggle the outside piece from the inside piece... inside piece 
__________________
The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer" |
|
|
|
|
09-29-2015, 05:40 PM
|
#3 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: Anyone know how to remove this?
looks like the left has a bit of silicone, that might be keeping it from wiggling apart too...
__________________
The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer" |
|
|
|
|
09-29-2015, 05:51 PM
|
#4 |
|
Registered User
Join Date: Oct 2014
Location: Mesa AZ (Near Phoenix)
Posts: 2,302
|
Re: Anyone know how to remove this?
It comes apart in two pieces. Just pull gently and wiggle side to side, each piece individually.
__________________
"Life is too short to drive a boring vehicle". Later, Wayne 
|
|
|
|
|
09-29-2015, 05:54 PM
|
#5 | |
|
Registered User
Join Date: Aug 2015
Location: Champaign, IL
Posts: 491
|
Re: Anyone know how to remove this?
Quote:
|
|
|
|
|
|
09-29-2015, 06:28 PM
|
#6 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: Anyone know how to remove this?
I use aan old sharp putty knife to ease around the perimeter of the box a little bit at a time to loosen it up till it is free
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
09-29-2015, 08:04 PM
|
#7 | |
|
Account Suspended
Join Date: Jan 2007
Location: Tucson
Posts: 2,183
|
Re: Anyone know how to remove this?
Quote:
|
|
|
|
|
|
09-29-2015, 09:07 PM
|
#8 |
|
Registered User
Join Date: Oct 2008
Location: Marianna Arkansas
Posts: 7,280
|
Re: Anyone know how to remove this?
Once separated from the firewall push the smaller of the harnesses through the bigger of the two halves. That is how I split the wiring harness from the front lamp harness. In reverse if your holding the big part put the small part in front of the clip then pull it back towards you. It will click in to lock. jim
|
|
|
|
|
09-29-2015, 11:02 PM
|
#9 |
|
Registered User
Join Date: Jul 2014
Location: Phoenix
Posts: 114
|
Re: Anyone know how to remove this?
You are all super awesome thank you for the replies! I'll let you know of the progress tomorrow!
|
|
|
|
|
10-01-2015, 12:41 AM
|
#10 |
|
Registered User
Join Date: Jul 2014
Location: Phoenix
Posts: 114
|
Re: Anyone know how to remove this?
You guys were right there was a little silicon holding the two pieces together, I just got a flat head screwdriver, and a hammer, and very gently got the two apart. Thanks!
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
