73 bb towers for 67 chevy trucks - The 1947 - Present Chevrolet & GMC Truck Message Board Network

mdg · 09-27-2003, 11:10 PM

Can anyone tell me if the motor mount towers on a 73 chevy truck can be used on a 67 chevy truck. I found a BB chevy motor at the pick and pull and want to replace the V6 motor that I have now. Any help would be greatly appreciated.

MDG

Longhorn Man · 09-27-2003, 11:21 PM

As far as direct bolt in, i don't think they'll work. But you should be able to make them work.
They are too tall if not mistaken.

Even if you can't make them work, you could clean them up and sell them on here for a little more than you'll spend.

mdg · 09-27-2003, 11:53 PM

If the 73's will not work, where can I buy the correct one's for my truck?

MDG

Longhorn Man · 09-27-2003, 11:59 PM

Actually, now that i think about it, the frame may need some modification for the big block engine. The fuel pump will be real close to (if not touching) the passenger side frame rail.
There are 2 kinds of big block mounts for the 68 - 72 trucks. The 68 - 71, which are a dime a dozen, but the motor mounts are expensive, and then there are the 72 which will cost an eye tooth, but the motor mounts are dirt cheap.
Check the parts board or start a 'big block towers wanted' thread.

**Bowtie468** · 09-28-2003, 12:14 AM

mdg,
Last week sometime, superchevy had a pair of '72 BB towers with mounts for sale. Look back a couple of pages or maybe PM him. He may still have them ! Good Luck !

Chris

**Bowtie468** · 09-28-2003, 12:22 AM

Sorry mdg, it looks like superchevy sold them ! If you want to see pics of them, the thread is on page 6 of the 67-72 parts board !

09-27-2003, 11:10 PM	#1
mdg Registered User Join Date: Nov 2002 Location: Apple Valley, California Posts: 26	73 bb towers for 67 chevy trucks Can anyone tell me if the motor mount towers on a 73 chevy truck can be used on a 67 chevy truck. I found a BB chevy motor at the pick and pull and want to replace the V6 motor that I have now. Any help would be greatly appreciated. MDG

09-28-2003, 12:14 AM	#5
Bowtie468 Senior Member Join Date: Jun 2002 Location: Cecilia, Louisiana Posts: 1,638	mdg, Last week sometime, superchevy had a pair of '72 BB towers with mounts for sale. Look back a couple of pages or maybe PM him. He may still have them ! Good Luck ! Chris __________________ Chris click here to see my buildpage http://67-72chevytrucks.com/vboard/s...d.php?t=394656 ---------------------------------- 1979 C10 Silverado Big10 SWB Factory 454/400 Cardinal Red/Santa Fe Tan (original paint) 1969 Camaro X44 LS swap 1968 C10 SWB Fleetside (SOLD) 468BBC MultiPort TPI / Dynamic EFI P4 Black/Black 1963 Nova SS convertible (SOLD) 194 I6/ PowerGlide

09-28-2003, 12:22 AM	#6
Bowtie468 Senior Member Join Date: Jun 2002 Location: Cecilia, Louisiana Posts: 1,638	Sorry mdg, it looks like superchevy sold them ! If you want to see pics of them, the thread is on page 6 of the 67-72 parts board ! __________________ Chris click here to see my buildpage http://67-72chevytrucks.com/vboard/s...d.php?t=394656 ---------------------------------- 1979 C10 Silverado Big10 SWB Factory 454/400 Cardinal Red/Santa Fe Tan (original paint) 1969 Camaro X44 LS swap 1968 C10 SWB Fleetside (SOLD) 468BBC MultiPort TPI / Dynamic EFI P4 Black/Black 1963 Nova SS convertible (SOLD) 194 I6/ PowerGlide

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-27-2003, 11:21 PM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	As far as direct bolt in, i don't think they'll work. But you should be able to make them work. They are too tall if not mistaken. Even if you can't make them work, you could clean them up and sell them on here for a little more than you'll spend.

09-27-2003, 11:53 PM	#3
mdg Registered User Join Date: Nov 2002 Location: Apple Valley, California Posts: 26	If the 73's will not work, where can I buy the correct one's for my truck? MDG

09-27-2003, 11:59 PM	#4
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Actually, now that i think about it, the frame may need some modification for the big block engine. The fuel pump will be real close to (if not touching) the passenger side frame rail. There are 2 kinds of big block mounts for the 68 - 72 trucks. The 68 - 71, which are a dime a dozen, but the motor mounts are expensive, and then there are the 72 which will cost an eye tooth, but the motor mounts are dirt cheap. Check the parts board or start a 'big block towers wanted' thread.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.