![]() |
![]() |
#1 |
Registered User
![]() Join Date: Oct 2015
Location: Dallas Texas
Posts: 1,380
|
Seat Belt Install
I'm getting ready to install my new seatlbelts from Morris. Am I correct in assuming that I will need to remove the bench seat to do this? Thanks
|
![]() |
![]() |
![]() |
#2 |
Senior Member
![]() Join Date: Feb 2009
Location: Northern Nevada
Posts: 7,249
|
Re: Seat Belt Install
I've only removed the re tractor belts, and that was with the seat in...3/16" head bolt and washer. I have the "luxury" of pulling everything, so the bench is coming out anyway. But, looks to me that no, you do not have to pull the seat. That is, unless your arms are shorter than 1.5'.
__________________
Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assembly kit for restoring the (a) truck from the ground up. My build thread, and more on the assembly kit https://67-72chevytrucks.com/vboard/...d.php?t=730025 |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Dec 2013
Location: Durango, CO
Posts: 827
|
Re: Seat Belt Install
I just installed my Morris belts without pulling the bench. It is definitely possible. But I won't say it was easy... a bit of contortionist posturing is necessary, and it helps to have a ratchet with very fine engagement for the bolts under the seat. A U-joint socket adapter helps too. Finally, make sure you PB Blaster the heck out of the seat belt bolts under the floor of the cab before you begin - sure makes it a lot easier to thread them out without fighting them every bit of the way.
__________________
1972 K10 Cheyenne Super | LWB, fleetside | 350/350/205 | KEEPER 1971 K10 Cheyenne | SWB, fleetside | LS Swap 5.3/4L60 | SOLD 1976 Trans Am | 400/4-spd | SOLD 1976 Trans Am | 455/4-spd | TOTALED ![]() |
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Oct 2015
Location: Dallas Texas
Posts: 1,380
|
Re: Seat Belt Install
Thanks to you both for your answers and hints.
|
![]() |
![]() |
![]() |
#5 |
Senior Member
![]() Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 6,286
|
Re: Seat Belt Install
I don't know about Morris belts, but I put my GM belts in my 70 with the seat in, slid all the way forward, and the gas tank in. Like mentioned, a fine tooth ratchet will be your friend. It was not bad, as I lubed the holes and cleaned the bolt threads with a wire wheel, and then lubed the bolt threads too. Good luck, post some pics before and after the install.
__________________
70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Power windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Dec 2013
Location: Durango, CO
Posts: 827
|
Re: Seat Belt Install
Haha! Didn't even think to try sliding the seat forward. That might have helped.
![]()
__________________
1972 K10 Cheyenne Super | LWB, fleetside | 350/350/205 | KEEPER 1971 K10 Cheyenne | SWB, fleetside | LS Swap 5.3/4L60 | SOLD 1976 Trans Am | 400/4-spd | SOLD 1976 Trans Am | 455/4-spd | TOTALED ![]() |
![]() |
![]() |
![]() |
#7 |
Senior Member
![]() Join Date: Feb 2009
Location: Northern Nevada
Posts: 7,249
|
Re: Seat Belt Install
I was introduced to an adjustable bench just last week. It hasn't worked since I bought it (1989)..........Very cool, only I'll be pulling the bench soon.
I couldn't seem to start my LH retract without a 13/16" wrench, which happened to be the only one I didn't have. $3 for an old thorsen combination at the local pawn shop.
__________________
Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assembly kit for restoring the (a) truck from the ground up. My build thread, and more on the assembly kit https://67-72chevytrucks.com/vboard/...d.php?t=730025 |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|