Mirror on my 67 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

walker · 10-04-2003, 07:44 PM

I just got the driver side rear view mirror for my 67 cst lwb. The original holes were welded up so I need a measurement for the screw holes, or just the first screw hole. It is the older looking round mirror. Also is the measurement the same for the driver side and passenger side?

walker · 10-05-2003, 01:01 AM

ttt

BLACK AND BLUE 67-72 · 10-05-2003, 01:21 AM

2 5/8" from front edge of the door and 1/2" down from the 2nd ridge down. Not the first ridge under the window, but the very next one down from that one.

This is on the driver's side, I am not sure on the passenger's because my truck does not have the mirror mounting holes. I will look in the assembly manual and see if they have anything on the passenger's side.

BLACK AND BLUE 67-72 · 10-05-2003, 01:37 AM

They are the same for both sides.

walker · 10-05-2003, 10:40 AM

Thanks fellers, I have been itching to get this installed but was afraid to drill in the wrong spot and have it look funny.

10-04-2003, 07:44 PM	#1
walker Registered User Join Date: Jul 2003 Location: north of Phx AZ about 30 miles Posts: 698	Mirror on my 67 I just got the driver side rear view mirror for my 67 cst lwb. The original holes were welded up so I need a measurement for the screw holes, or just the first screw hole. It is the older looking round mirror. Also is the measurement the same for the driver side and passenger side? __________________ Andy,Phx AZ '67 C-10 (Ahhh, done at last. Well there is that disk front end I want to put in and...) "23 C-Cab-sold '48 Ford 8N tractor(still working) '67 Scout(Now on the road) '70 MG B.-sold

10-05-2003, 01:01 AM	#2
walker Registered User Join Date: Jul 2003 Location: north of Phx AZ about 30 miles Posts: 698	ttt __________________ Andy,Phx AZ '67 C-10 (Ahhh, done at last. Well there is that disk front end I want to put in and...) "23 C-Cab-sold '48 Ford 8N tractor(still working) '67 Scout(Now on the road) '70 MG B.-sold

10-05-2003, 01:21 AM	#3
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	2 5/8" from front edge of the door and 1/2" down from the 2nd ridge down. Not the first ridge under the window, but the very next one down from that one. This is on the driver's side, I am not sure on the passenger's because my truck does not have the mirror mounting holes. I will look in the assembly manual and see if they have anything on the passenger's side. __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA

10-05-2003, 01:37 AM	#4
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	They are the same for both sides. __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA

10-05-2003, 10:40 AM	#5
walker Registered User Join Date: Jul 2003 Location: north of Phx AZ about 30 miles Posts: 698	Thanks fellers, I have been itching to get this installed but was afraid to drill in the wrong spot and have it look funny. __________________ Andy,Phx AZ '67 C-10 (Ahhh, done at last. Well there is that disk front end I want to put in and...) "23 C-Cab-sold '48 Ford 8N tractor(still working) '67 Scout(Now on the road) '70 MG B.-sold

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.