![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Jul 2012
Location: Texas
Posts: 78
|
A/C in this non-A/C cab
I would like to install Vintage Air in this non-A/C cab with vents and controls that look factory. How difficult is this to do?
|
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Mar 2018
Location: Barrington nh
Posts: 104
|
Re: A/C in this non-A/C cab
Buy the vintage AC kit for trucks with AC. Then buy an AC dash bezel and AC dash pad insert from LMC or whoever and it will look factory with h the exception of the vintage unit under the dash.
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Sep 2002
Location: Liberty, Mississippi
Posts: 671
|
Re: A/C in this non-A/C cab
That's a clean truck Jake!
Nice ride |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Nov 2016
Location: Olathe Kansas
Posts: 3
|
Re: A/C in this non-A/C cab
Just download the instruction from Vintage Air for the SureFit series for your truck to get a feel for what it takes to put it in. Ordered mine for my '74 a couple of weeks ago and got it within a week. Haven't installed it yet but instructions are thorough and looks straightforward. Talked to them on the phone due to a couple of modifications I have and they are very knowledgeable. Their national sales manager is a chevy truck guy, so I'm sure that has something to do with their Sure Fit series covering all the years.
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Dec 2011
Location: Massachusetts
Posts: 243
|
Re: A/C in this non-A/C cab
Incidentally I learned after calling Vintage Air that the non-AC and AC kits are the same part number now. I called about it cause I got confused when ordering and noticed that. I haven't installed yet but it looks pretty straight forward.
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jul 2007
Location: Tucson, AZ
Posts: 3,188
|
Re: A/C in this non-A/C cab
I was just looking at a 1973 square at the local Pull A Part and most of the factory a/c parts seem to be there. However, I think you would be better off with the Vintage Air system. As I recall, the firewall is different between the a/c and non a/c cabs.
I think the VA parts are mostly under the dash, so you would not have to hack your dash or firewall. I think you have to shorten your glove box also and they give you a kit for that. I would not attempt to go for a stock look if I were you. You already are modifying the truck to non- stock by adding a/c, so the VA system is the best choice. If they offer an electronic HVAC control rather than a mechanical control I would go with that. |
![]() |
![]() |
![]() |
#7 | |
Registered User
Join Date: Jun 2004
Location: Spartanburg, SC
Posts: 1,963
|
Re: A/C in this non-A/C cab
Quote:
Fyi for factory a/c kit they tell you to modify the vent duct that goes over to the Dr side dash vent. I left the plastic piece out an just ran the hose they send over to it. It fit in the area between the dash an steering column better than the factory plastic duct. Part of that could be due to where I moved the steering column 2" further into the dash.
__________________
Paul '78 GMC Serria 15 Heavy Half. 361/NV3500/3.73. Former LWB NV3500 swap Trailing arm swap '98 ECSB Z71 daily driver -traded ![]() '03 burb. Family cruiser http://upstategmtrucks.com/ |
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jun 2003
Location: ga
Posts: 630
|
Re: A/C in this non-A/C cab
many years back I took everything from a 77 k20 ac cab to and used it in my 79 k20 non a/c cab best I remember I had to cut out the square a little bit out the firewall for the evaparator core and I had to drill out the holes to move the heater hoses and used everything from the 77 so I know it can be done.]
__________________
4x4k30 if trouble was money i would have plenty Last edited by 4x4k30; 01-19-2019 at 12:55 PM. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|