|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
03-31-2019, 11:29 AM
|
#1 |
|
Registered User
Join Date: May 2010
Location: washington nj
Posts: 44
|
Jack for my 1965 C-10 what is a good option?
Hi All, I need to buy a jack for my 65 C-10. I need something to tuck away in the truck. It would need to be able to get under the truck with a flat tire. I tried my bottle jack but when the tire was down I could not get it under the axle nor would it look safe to even do on frame or rear. I thought farm jack or bumper jack but they are bulky to store..perhaps a good scissor jack and add a rubber pad on top? My floor jack is fine at home but obviously no use on the road.. Any ideas?
|
|
|
|
03-31-2019, 11:42 AM
|
#2 |
|
1965 Chevy C10, 2005 4.8L/4l60
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,546
|
Re: Jack for my 1965 C-10 what is a good option?
My truck is lowered so...
What I do is I have a hydraulic jack in a case, jack the frame up, use a jack stand and then put the hydraulic jack under the crossmember.
__________________
Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684  support our troops! |
|
|
|
|
03-31-2019, 11:43 AM
|
#3 |
|
Moderator
  
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: Jack for my 1965 C-10 what is a good option?
Don't they sell small floor jacks that can fit behind the seat on these trucks? I bet you can find one. Or a scissor jack, ya that'd work.
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
|
|
|
|
03-31-2019, 12:32 PM
|
#4 |
|
Registered User
Join Date: May 2010
Location: washington nj
Posts: 44
|
Re: Jack for my 1965 C-10 what is a good option?
I will look into the setup you have Clyde.. as for behind the seat. No.. the gas tank is behind so no room there.. but I think a scissor would fit under but it would need to be heavy enough and high enough. I was hoping someone had found one that gave enough lift.
|
|
|
|
|
03-31-2019, 12:32 PM
|
#5 |
|
Registered User
Join Date: Sep 2014
Location: Valparaiso, IN
Posts: 300
|
Re: Jack for my 1965 C-10 what is a good option?
I use a screw jack that fits where the gas tank used to sit. It' old & scratched but I'll look for the brand name. Here is a short review.
https://www.thedrive.com/reviews/268...-scissor-jacks |
|
|
|
|
03-31-2019, 12:39 PM
|
#6 |
|
Registered User
Join Date: Sep 2014
Location: Valparaiso, IN
Posts: 300
|
Re: Jack for my 1965 C-10 what is a good option?
|
|
|
|
|
03-31-2019, 02:08 PM
|
#7 |
|
Registered User
Join Date: Feb 2012
Location: pleasant valley--placerville ca
Posts: 3,039
|
Re: Jack for my 1965 C-10 what is a good option?
look for one from a later chevy silverado scissor type.
__________________
1961 chevy K10 my build is------------61K10 build |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
