![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Stylin
Join Date: Sep 2001
Location: Tuttle, OK
Posts: 620
|
th350c to th350 conversion
ok i read threw my th350 book and it shows a conversion kit to convert a lockup style 350 to a non lockup style. is there any visible difference between a lockup style converter and a non lockup style?
thanks Paul i also posted on the engine&drivetrain board, just thought id post here also since everybody questioned my retardedness when i mention a th350c lol ![]()
__________________
Ive been traveling for some time, with my fishin pole and my bottle of shyne. Most Girls like finished products and just dont understand what a good addiction does for you http://www.paulwall.us/ |
![]() |
![]() |
![]() |
#2 |
Slots go on anything!
Join Date: May 2003
Location: Richardson, TX
Posts: 5,957
|
I think there is another set of splines on the output shaft of the trans, like on a 700R4. If so, I would guess there should be a corresponding set inside the converter? I have never had a 350C out to know 100%, but I know it to be true on a lockup 700. Hope this halps a little.
__________________
1974 Jimmy- 5.3/4L80e/NP241 |
![]() |
![]() |
![]() |
#3 |
Stylin
Join Date: Sep 2001
Location: Tuttle, OK
Posts: 620
|
well the kit in the book listed the front pump, new spline, n other parts needed to be able to go regular th350 but not change the rest of the trans. im just wondering if the lockup tc's are larger in diameter than a regular tc
__________________
Ive been traveling for some time, with my fishin pole and my bottle of shyne. Most Girls like finished products and just dont understand what a good addiction does for you http://www.paulwall.us/ |
![]() |
![]() |
![]() |
#4 |
Slots go on anything!
Join Date: May 2003
Location: Richardson, TX
Posts: 5,957
|
FWIW, you might be better off just getting an older TH350, as the cost of the pump and input shaft would probably be around the same as getting an exchange rebuilt one. They usually go about $250-300 exchange here in Dallas, I would bet it is probably close to that in OKC. If your trans is working OK, it would make a good exchange unit.
__________________
1974 Jimmy- 5.3/4L80e/NP241 |
![]() |
![]() |
![]() |
#5 |
Insert Witty Text Here
Join Date: Oct 2002
Location: San Antonio, TX
Posts: 3,415
|
Why convert? If you don't like the lockup, just disconnect it or put it on a switch.
If your transmission is bad, then just ignore this post. ![]() Slonaker |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: May 2003
Location: South Carolina
Posts: 104
|
The non lockup t/c is smaller and lighter than the lockup but from what I understand from the guy who built mine is there are a couple other things to change including some drilling I would go with jonboy's idea and get another tranny. I just got mine here for 350 and it is sweet .
Steve ![]() ![]() |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: May 2003
Location: Shreveport LA
Posts: 3,170
|
Just unhook it. I bought my 79 Sub about 5 years ago with a bad trans & I replaced it with a rebuilt 350C, which works fine unhooked. If I remember correctly (and this is debatable), the 350C converter had a raised flat area on the front, as opposed to a regular 350 converter which did not.
|
![]() |
![]() |
![]() |
#8 |
Slots go on anything!
Join Date: May 2003
Location: Richardson, TX
Posts: 5,957
|
the raised flat area at the front is the actual lockup clutch. A normal 350 TC will be round at the front and rear.
I don't know a whole lot about the 350C. I do know that if the lockup is not working on a 700, it will overheat. Will disconnecting the lockup on a 350C do the same thing? I have had it happen when the speedo cable broke on my el Camino, and it got hot enough that the engine temp was raised. It also set a check engine light, with a TCC fault code. That is why I would be hesiant about just disconnecting it. If your trans is fine, it would get you by for a while. A regular 350 converter might be the way to go there. If you are putting in a converter, you almost have the trans out. If it is the original trans, then you have at least 17 years of use on it. That is why I would suggest a 350 swap, and it is (relatively) cheap, if you do the labor yourself.
__________________
1974 Jimmy- 5.3/4L80e/NP241 |
![]() |
![]() |
![]() |
#9 |
Stylin
Join Date: Sep 2001
Location: Tuttle, OK
Posts: 620
|
Thank you jonboy your the only one thats answered my question. I only wanted to know about the tc, not everything else. my trans has been unhooked from the day i purchased it and its outlived a rebuilt 305. sry if i come off as an arsehole but tech support for my outgoing mail server has been nothing but SH*T. They have yet to answer my question of why i cant log on, 8 replys and they tell me how to set it up in each reply even tho i could log on just fine 2 weeks ago.
__________________
Ive been traveling for some time, with my fishin pole and my bottle of shyne. Most Girls like finished products and just dont understand what a good addiction does for you http://www.paulwall.us/ |
![]() |
![]() |
![]() |
#10 |
Slots go on anything!
Join Date: May 2003
Location: Richardson, TX
Posts: 5,957
|
no prob, man. That's why we are all here.
![]()
__________________
1974 Jimmy- 5.3/4L80e/NP241 |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|