Another Frame Crossmember Question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

C.I.Blazer · 09-29-2019, 11:32 PM

Trying to figure out what is original, modified, or missing from my frame. I have noticed that in number of frames in some of the builds have a crossmember that sits right behind the transfer case. What is the purpose of this cross member? I do not see it on the frame spec sheets I have downloaded and mine does not have it.

Here are a couple of pics I took from another thread.

litebulblsc · 09-30-2019, 04:54 AM

The second crossmember is for ones equipped with a skid plate

C.I.Blazer · 09-30-2019, 07:38 AM

Thanks for the info!

**jaros44sr** · 09-30-2019, 08:59 AM

In the second pic you can see the bracket that connects the frame to NP 205, lots off discussions on whether to use this bracket or not, possible trans. housing breakage...

C.I.Blazer · 09-30-2019, 04:20 PM

Hmmm. I do have the bracket for the TC. Did not realize it was a controversial item. I am not doing any hardcore offroading so I will hopefully be OK.

**jaros44sr** · 09-30-2019, 06:20 PM

Quote:

Originally Posted by C.I.Blazer

Hmmm. I do have the bracket for the TC. Did not realize it was a controversial item. I am not doing any hardcore offroading so I will hopefully be OK.

Well, if it were a good thing, wouldn't GM continue to use it after '72. There is a rather long thread on it somewhere on this site, with a rather compelling discussion against using it. Although I have a 'K' case to put in the jimmy, not sure on the bracket

litebulblsc · 09-30-2019, 07:40 PM

Quote:

Originally Posted by C.I.Blazer

Hmmm. I do have the bracket for the TC. Did not realize it was a controversial item. I am not doing any hardcore offroading so I will hopefully be OK.

I am sure you will be fine. Plenty of people use it without issue.

09-29-2019, 11:32 PM	#1
C.I.Blazer Registered User Join Date: Aug 2019 Location: WA State Posts: 186	Another Frame Crossmember Question Trying to figure out what is original, modified, or missing from my frame. I have noticed that in number of frames in some of the builds have a crossmember that sits right behind the transfer case. What is the purpose of this cross member? I do not see it on the frame spec sheets I have downloaded and mine does not have it. Here are a couple of pics I took from another thread. Attached Images

09-30-2019, 04:54 AM	#2
litebulblsc Registered User Join Date: Aug 2006 Location: LaSalle Mi Posts: 525	Re: Another Frame Crossmember Question The second crossmember is for ones equipped with a skid plate

09-30-2019, 07:38 AM	#3
C.I.Blazer Registered User Join Date: Aug 2019 Location: WA State Posts: 186	Re: Another Frame Crossmember Question Thanks for the info!

09-30-2019, 08:59 AM	#4
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,761	Re: Another Frame Crossmember Question In the second pic you can see the bracket that connects the frame to NP 205, lots off discussions on whether to use this bracket or not, possible trans. housing breakage... __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

09-30-2019, 04:20 PM	#5
C.I.Blazer Registered User Join Date: Aug 2019 Location: WA State Posts: 186	Re: Another Frame Crossmember Question Hmmm. I do have the bracket for the TC. Did not realize it was a controversial item. I am not doing any hardcore offroading so I will hopefully be OK.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.