|
09-02-2020, 12:29 PM
|
#1 |
|
Registered User
Join Date: Jul 2019
Location: Beebe, AR
Posts: 2,475
|
Dust Shield Question
OK folks, I got a conundrum. I am putting the front end back together and am almost to the point of needing dust shields. I have this set of '73 spindles with these factory dust shields I could pull, clean up and use or I could pop $50 for a set of new repops.
What are the thoughts here? These have two "slots" for lack of a better term but most I see repop are solid.
__________________
1967 C10 1980 Jeep CJ5 2020 Toyota 4Runner 2024 Toyota Tundra Last edited by 67C10Step; 09-02-2020 at 01:26 PM. |
|
|
|
09-02-2020, 12:39 PM
|
#2 |
|
Registered User
Join Date: Jun 2002
Location: Tucson AZ by way of WI & CA
Posts: 510
|
Re: Dust Shield Question
Spend the money on shiny go fast bits.
|
|
|
|
|
09-02-2020, 12:49 PM
|
#3 |
|
Senior Member
 
Join Date: Sep 2014
Location: Wenatchee, Wa
Posts: 929
|
Re: Dust Shield Question
Those look good, I would use them.
|
|
|
|
|
09-02-2020, 01:16 PM
|
#4 |
|
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,945
|
Re: Dust Shield Question
If they will work use them. Save the $50.00 for something you don't have. If the 73 will fit clean them up and install, they will never be seen so don't go to a bunch of trouble on them. Well unless your going for show instead of go!
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
|
|
|
|
09-02-2020, 01:31 PM
|
#5 |
|
Registered User
Join Date: Jul 2019
Location: Beebe, AR
Posts: 2,475
|
Re: Dust Shield Question
Right now I am working on the woah! before the go! Thirty plus years ago it would have been the other way around.
This truck is a budget build. Not a daily driver but definitely will be driver quality all the way. I think I'll clean them up and see how they fit. Worst case is I'll stick them back on the 73 spindles and hold onto it all. Here is my current state of things:
__________________
1967 C10 1980 Jeep CJ5 2020 Toyota 4Runner 2024 Toyota Tundra |
|
|
|
|
09-02-2020, 03:45 PM
|
#6 | |
|
Registered User
Join Date: Jun 2014
Location: Tahuya WA
Posts: 616
|
Re: Dust Shield Question
Quote:
Clean them up and paint to match your frame and control arms. If anybody ever does bother to notice them, they'll still have plenty of "woah". 
|
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
