|
09-09-2024, 12:42 PM
|
#1 |
|
Senior Member
 
Join Date: Jan 2001
Location: Orem, Utah
Posts: 7,976
|
Roll Bar Wrap
I have a roll bar (Fat Bar) in my Blazer and I'd like to pad it somehow. I bought some self-adhesive neoprene but it is too stiff to lay flat when I try to spiral wrap it.
Any ideas?
__________________
I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man. - Thomas Jefferson |
|
|
|
09-09-2024, 01:09 PM
|
#2 |
|
Post Whore
Join Date: Feb 2016
Location: Portland Oregon
Posts: 11,350
|
Re: Roll Bar Wrap
What diameter of bar?
__________________
Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help.  RIP Bob Parks. 1967 Burban (the WMB),1988 S10 Blazer (the Stink10 II),1969 GTO (the Goat), 1970 Javelin, 1952 F2 Ford OHC six 4X4, 29 Model A, 72 Firebird (the DBP Bird). 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377 |
|
|
|
09-09-2024, 01:54 PM
|
#3 |
|
Registered User
Join Date: May 2009
Location: Motor City
Posts: 9,226
|
Re: Roll Bar Wrap
https://www.summitracing.com/search/...rder=Ascending
The actual SFI approved padding is pretty hard. Some of the JCI/more open cell padding might be better in this case. Or - just use the plumbing wrap from the hardware store, if you are going for looks and a bit of cushion. K
__________________
Chevrolet Flint Assembly 1979-1986 GM Full Size Truck Engineering 1986 - 2019 Intro from an Old Assembly Guy: http://67-72chevytrucks.com/vboard/s...d.php?t=342926 My Pontiac story: http://forums.maxperformanceinc.com/...d.php?t=560524 Chevelle intro: http://www.superchevy.com/features/s...hevy-chevelle/ |
|
|
|
|
09-09-2024, 03:52 PM
|
#4 |
|
Senior Member
Join Date: Feb 2022
Location: Ca
Posts: 630
|
Re: Roll Bar Wrap
This was my source for most of my racing stuff.https://www.pegasusautoracing.com/gr...p?GroupID=ROLL
|
|
|
|
|
09-11-2024, 10:37 PM
|
#5 |
|
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,727
|
Re: Roll Bar Wrap
Wild Horses is a vendor mostly of Bronco parts, but they sell custom roll bar pads with zip on vinyl covers. Like large BMX bike pads! They are custom ordered to your specs. At lest for 2” tubes. Did these on my kids ‘72 Jimmy cage and the cage in my CJ-5. Highly recommend. My own Jimmy has the pipe insulation and electrical tape covering on it I installed back in 1991!
https://www.wildhorses4x4.com/headba...m-roll-bar-pad
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
