|
01-19-2004, 02:35 PM
|
#1 |
|
Post Whore
 
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
|
Panhard questions
A buddy of mine likes to make stuff rather than buy it. He wants to make a panhard bar for the truck he is building. He is considering using Schedule 80 3/8" black pipe, od is .675" and id is .423 and he is going to drill and tap for a 1/2" fine thread Heim joint. The Heim joints have 1/2" holes to affix to the axle tube and frame.
Anyone have thoughts on whether that setup is strong enough for a panhard bar? Also, is there a specific angle he should try to have the panhard bar at? The specific application is a 1965 Chevy C10 with a 1972 coil spring truck rearend.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 Last edited by Yukon Jack; 01-19-2004 at 02:41 PM. |
|
|
|
01-19-2004, 03:11 PM
|
#2 |
|
Wiseass secured himself a BAN
Join Date: Nov 2000
Location: MOON!!!
Posts: 2,282
|
Plastic or metal?
|
|
|
|
|
01-19-2004, 03:34 PM
|
#3 |
|
Progress = 0%
Join Date: Nov 2001
Location: Kansas City, MO
Posts: 2,108
|
Ideally it should be horizontal (no angle). This will provide the least amount of side to side travel.
__________________
Jason - '67 GMC swb | '57 Bel-Air 4dr hardtop | '56 210 4dr Wagon | 2000 GMC Sierra |
|
|
|
|
01-19-2004, 03:50 PM
|
#4 |
|
Registered User
Join Date: May 2000
Location: Frankfort, Kentucky, USA
Posts: 2,163
|
It should also be as long as possible
__________________
'69 CST Short fleetside Lowered, 400 small block, 700R4, 4 wheel disc brakes, front sway bar & rear camaro sway bar (in progress) '87 V10 4x4 Short Fleetside Quad Suspension and Dual Tanks |
|
|
|
|
01-19-2004, 04:00 PM
|
#5 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
|
It is metal pipe.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
01-19-2004, 04:29 PM
|
#6 |
|
Wiseass secured himself a BAN
Join Date: Nov 2000
Location: MOON!!!
Posts: 2,282
|
It should work. It may loosen up over time due to it being hollow.
|
|
|
|
|
01-19-2004, 04:51 PM
|
#7 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
|
Are they normally solid?
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
01-19-2004, 04:54 PM
|
#8 |
|
Registered User
Join Date: May 2000
Location: Frankfort, Kentucky, USA
Posts: 2,163
|
I bought one from ECE that is tube with threaded ends welded on
__________________
'69 CST Short fleetside Lowered, 400 small block, 700R4, 4 wheel disc brakes, front sway bar & rear camaro sway bar (in progress) '87 V10 4x4 Short Fleetside Quad Suspension and Dual Tanks |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
