rear axle size difference confusion - The 1947 - Present Chevrolet & GMC Truck Message Board Network

FirstGen · 02-14-2004, 01:09 AM

Ok, I'm alittle confused. I've heard that the 5 lug axles are only 3/8 inch longer than the older 6 lug. However, this thread says that the rear end is 1.25 inches larger? Which is it?
http://67-72chevytrucks.com/vboard/s...threadid=79939
What years have the larger rear and which have the smaller one?
Lastly, what is the benefit to switching to 5 lug besides being able to use a 5 lug wheel design?
Thanks.

Longhorn Man · 02-14-2004, 01:16 AM

5 lug has disc brakes up front, and that is the main reason for getting them. You can get 6 lug rotors, but they are not cheap.
The '70 rear may or may not be wide or narrow, that was the conversion rear end, later ones were wide and 5 lug axle shafts slide right in.
The 3/8 measurement is per side, still doesn't explain the 1 1/4 inch deal, but I have heard from amny people on the 3/8 deal, and a few of them made spacers off that measurement and it worked, so I'll go by that.

FirstGen · 02-14-2004, 01:28 AM

so it's cheaper to get the whole 5 lug disk setup and rear axle swap than buying front 6 lug rotors/calipers? What all do you need to do this conversion? Any tips?

SS55 · 02-14-2004, 01:40 AM

You could have your rear axles re-done for 5 lug. I had a pair done a few years ago. I think I sent them to Moser Engineering. Seems like it was $75 for the pair back about 10-12 years ago.

Darrell

Longhorn Man · 02-14-2004, 01:43 AM

I don't know if it would be cheaper to do the 5 lug than the 6 lug rotors...I highly doubt it actually.
The 6 lug rotors go on just like the 5 lug ones. I don't think they are way over priced, just more expensive (Since they are aftermarket only) than the 5 lug counterparts that you can pick up at any parts store in america.

MOTHERTRUCKERS · 02-14-2004, 08:55 AM

Anybody try 6 lug 89-90 3/4 ton light duty rotors? same inner/outer bearing and seal part numbers as 71-2 rotors.

Bowtie67 · 02-14-2004, 05:38 PM

Actually the only 1 reason I would swap out front rotor to a 5 lug setup would be for better availability, you cant walk into an autoparts place say you have a 69 with 6 liug rotors on it they don't make them. but you caan get 5 lug rotors a lot cheaper because they are more common unless you end up ordering from a specialty place like ECE, CPP, etc.

02-14-2004, 01:09 AM	#1
FirstGen Just Don't Stop! Join Date: Feb 2004 Location: Dallas Posts: 1,239	rear axle size difference confusion Ok, I'm alittle confused. I've heard that the 5 lug axles are only 3/8 inch longer than the older 6 lug. However, this thread says that the rear end is 1.25 inches larger? Which is it? http://67-72chevytrucks.com/vboard/s...threadid=79939 What years have the larger rear and which have the smaller one? Lastly, what is the benefit to switching to 5 lug besides being able to use a 5 lug wheel design? Thanks. __________________ 1968 C10 build in process TT LSA/6L90e/9" Last edited by FirstGen; 02-14-2004 at 01:12 AM.

02-14-2004, 01:28 AM	#3
FirstGen Just Don't Stop! Join Date: Feb 2004 Location: Dallas Posts: 1,239	so it's cheaper to get the whole 5 lug disk setup and rear axle swap than buying front 6 lug rotors/calipers? What all do you need to do this conversion? Any tips? __________________ 1968 C10 build in process TT LSA/6L90e/9"

02-14-2004, 01:40 AM	#4
SS55 Registered User Join Date: Nov 2003 Location: San Diego, CA Posts: 62	You could have your rear axles re-done for 5 lug. I had a pair done a few years ago. I think I sent them to Moser Engineering. Seems like it was $75 for the pair back about 10-12 years ago. Darrell __________________ Be wary of the light at the end of the tunnel....It might be a gorilla holding a flashlight! 71 Blazer, ex-4WD...Bought it that way 55 GMC 55 Belair 2dr HT 67 El Camino

02-14-2004, 08:55 AM	#6
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	Anybody try 6 lug 89-90 3/4 ton light duty rotors? same inner/outer bearing and seal part numbers as 71-2 rotors. __________________ Rest in Peace Ed. Thanks for all the good times.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-14-2004, 01:16 AM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	5 lug has disc brakes up front, and that is the main reason for getting them. You can get 6 lug rotors, but they are not cheap. The '70 rear may or may not be wide or narrow, that was the conversion rear end, later ones were wide and 5 lug axle shafts slide right in. The 3/8 measurement is per side, still doesn't explain the 1 1/4 inch deal, but I have heard from amny people on the 3/8 deal, and a few of them made spacers off that measurement and it worked, so I'll go by that.

02-14-2004, 01:43 AM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	I don't know if it would be cheaper to do the 5 lug than the 6 lug rotors...I highly doubt it actually. The 6 lug rotors go on just like the 5 lug ones. I don't think they are way over priced, just more expensive (Since they are aftermarket only) than the 5 lug counterparts that you can pick up at any parts store in america.

02-14-2004, 05:38 PM	#7
Bowtie67 Registered User Join Date: Jan 2004 Location: NH Posts: 2,266	Actually the only 1 reason I would swap out front rotor to a 5 lug setup would be for better availability, you cant walk into an autoparts place say you have a 69 with 6 liug rotors on it they don't make them. but you caan get 5 lug rotors a lot cheaper because they are more common unless you end up ordering from a specialty place like ECE, CPP, etc.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.