Pics needed, I'm really close... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

red71cheyenne · 12-09-2005, 02:06 AM

To getting to start the Blazer up and run the engine. I need some pics of the clutch linkage though. I have a stock 350 with a stock 4 speed, I think SM465. I need to make sure my linkage is right though. Could someone post pics of their linkage including the z-bar and return spring? I think any 4wd truck would work. Thanks, Jeff.

**dennislbrooks** · 12-09-2005, 02:00 PM

If I remember, I will get you a couple pics from the build book when I get home today. Work gets in my way sometimes.

red71cheyenne · 12-09-2005, 05:16 PM

Thanks Dennis. Ya, can't wait til I retire so work will be the trucks. Jeff.

**dennislbrooks** · 12-09-2005, 06:28 PM

Dang, I have not figured out the logical order of the build book - no index. Here is a pic of a right hand drive for a 6 cylinder--think in opposite. I will keep looking for the left hand V8. Will stumble across it someday.

red71cheyenne · 12-09-2005, 08:20 PM

Duh, I have one of those, might ought to look at it. Thanks Dennis! Jeff.

mudpuppie · 12-09-2005, 08:37 PM

was working on mine ...... 2 wd

red71cheyenne · 12-10-2005, 11:11 PM

Sweet! Thanks Mudpuppie! Thats what I was looking for. Funny though, mine doesn't have that bracket that goes to the tranny bolt. Is your ball stud mounted to the engine? Mine is. Thanks, Jeff.

mudpuppie · 12-11-2005, 08:57 AM

Not konowing if its orignial , just what i have .......

knsmodels · 12-12-2005, 01:25 AM

Red.....the 2wd is different than the 4wd.....like you said your ball stud is mounted to the engine block farther up without the bracket.....I will try and get you pics of mine tomorrow if no one else comes up with any.....LMC catalog has pretty good pics of the linkage if I remember correctly....Paul

red71cheyenne · 12-12-2005, 02:56 PM

kns, thanks ya, lmc shows some of the linkage, but not where the ball stud is on the engine or where the return spring goes. It doesn't show the bracket on mudpuppies setup either. I'm just wanting to make sure mine is hooked up right before I start it up and try to drive it down the road. The assembly manual is a little vague too, except on the 6 cyl. model. Jeff.

knsmodels · 12-12-2005, 03:59 PM

red......hope these help.......I had the inner fender out last week and that would have been the perfect time for pics.....but this is the best I can do....let me know if there is something specific you need to know....

red71cheyenne · 12-12-2005, 06:38 PM

Those are perfect! That is exactly what I needed. By the way, sweet looking engine and exhaust! Looks like mine will look when I'm done. Is that a heat riser I see there?

knsmodels · 12-12-2005, 11:21 PM

red.....thanks for the comments.....just finished the truck in the beginning of the Summer.....it is pretty much stock so yeah that's the heat riser tube you see there.....Let me know if you need anything else.....

12-09-2005, 02:06 AM	#1
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	Pics needed, I'm really close... To getting to start the Blazer up and run the engine. I need some pics of the clutch linkage though. I have a stock 350 with a stock 4 speed, I think SM465. I need to make sure my linkage is right though. Could someone post pics of their linkage including the z-bar and return spring? I think any 4wd truck would work. Thanks, Jeff. __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

12-09-2005, 02:00 PM	#2
dennislbrooks Senior Member Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,787	Re: Pics needed, I'm really close... If I remember, I will get you a couple pics from the build book when I get home today. Work gets in my way sometimes.

12-09-2005, 05:16 PM	#3
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	Re: Pics needed, I'm really close... Thanks Dennis. Ya, can't wait til I retire so work will be the trucks. Jeff. __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

12-09-2005, 06:28 PM	#4
dennislbrooks Senior Member Join Date: Feb 2004 Location: Williamsburg, Ohio Posts: 1,787	Re: Pics needed, I'm really close... Dang, I have not figured out the logical order of the build book - no index. Here is a pic of a right hand drive for a 6 cylinder--think in opposite. I will keep looking for the left hand V8. Will stumble across it someday. Attached Images Last edited by dennislbrooks; 12-09-2005 at 06:28 PM.

12-09-2005, 08:20 PM	#5
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	Re: Pics needed, I'm really close... Duh, I have one of those, might ought to look at it. Thanks Dennis! Jeff. __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

12-09-2005, 08:37 PM	#6
mudpuppie Registered User Join Date: Nov 2005 Location: Virginia Posts: 51	Re: Pics needed, I'm really close... was working on mine ...... 2 wd

12-10-2005, 11:11 PM	#7
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	Re: Pics needed, I'm really close... Sweet! Thanks Mudpuppie! Thats what I was looking for. Funny though, mine doesn't have that bracket that goes to the tranny bolt. Is your ball stud mounted to the engine? Mine is. Thanks, Jeff. __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

12-11-2005, 08:57 AM	#8
mudpuppie Registered User Join Date: Nov 2005 Location: Virginia Posts: 51	Re: Pics needed, I'm really close... Not konowing if its orignial , just what i have .......

12-12-2005, 01:25 AM	#9
knsmodels I make Models Join Date: May 2005 Location: Bucks, PA Posts: 626	Re: Pics needed, I'm really close... Red.....the 2wd is different than the 4wd.....like you said your ball stud is mounted to the engine block farther up without the bracket.....I will try and get you pics of mine tomorrow if no one else comes up with any.....LMC catalog has pretty good pics of the linkage if I remember correctly....Paul __________________ Click to see what I do 1972 LWB K10 350/4 sp 1968 SS Chevelle 396/tremac5spd

12-12-2005, 02:56 PM	#10
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	Re: Pics needed, I'm really close... kns, thanks ya, lmc shows some of the linkage, but not where the ball stud is on the engine or where the return spring goes. It doesn't show the bracket on mudpuppies setup either. I'm just wanting to make sure mine is hooked up right before I start it up and try to drive it down the road. The assembly manual is a little vague too, except on the 6 cyl. model. Jeff. __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

12-12-2005, 03:59 PM	#11
knsmodels I make Models Join Date: May 2005 Location: Bucks, PA Posts: 626	Re: Pics needed, I'm really close... red......hope these help.......I had the inner fender out last week and that would have been the perfect time for pics.....but this is the best I can do....let me know if there is something specific you need to know.... __________________ Click to see what I do 1972 LWB K10 350/4 sp 1968 SS Chevelle 396/tremac5spd Last edited by knsmodels; 12-12-2005 at 04:01 PM.

12-12-2005, 06:38 PM	#12
red71cheyenne Back in the sticks Join Date: Jan 2001 Location: Fordland, MO Posts: 3,188	Re: Pics needed, I'm really close... Those are perfect! That is exactly what I needed. By the way, sweet looking engine and exhaust! Looks like mine will look when I'm done. Is that a heat riser I see there? __________________ 1971 Cheyenne C-10 w/700R4 and Tuned Port Injection 1969 K5 Blazer w/Tuned Port 2010 2SS/RS Flaming Orange Camaro 2011 K1500 Suburban 2014 K1500 Pickup 2008 Nissan Altima? The wifes' hoopty

12-12-2005, 11:21 PM	#13
knsmodels I make Models Join Date: May 2005 Location: Bucks, PA Posts: 626	Re: Pics needed, I'm really close... red.....thanks for the comments.....just finished the truck in the beginning of the Summer.....it is pretty much stock so yeah that's the heat riser tube you see there.....Let me know if you need anything else..... __________________ Click to see what I do 1972 LWB K10 350/4 sp 1968 SS Chevelle 396/tremac5spd



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.