Autometer guage bezels guys.. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**FRENCHBLUE72** · 12-15-2005, 09:50 PM

What autometer guages do you guys run-oil pressure- water temp-volts-tach and speedo.. What do you guys run in the other two holes????

rocknss · 12-15-2005, 10:12 PM

I use a Brothers billet dash bezel with Autometer Phantom guages.

71swb4x4 · 12-15-2005, 10:23 PM

Fuel gauge would be a good one.
My last one is tranny temp.

**FRENCHBLUE72** · 12-15-2005, 11:09 PM

Ya I guess that a fuel guage would be a good idea.. That would be the one for the center hole correct??? But hard to find also??

pebbleboy · 12-15-2005, 11:50 PM

I was hoping to cram
5in: speedo tach

2 5/8: Fuel, Volt, Water Temp, Oil Pressure, Trans temp, And either a vacuum or clock

My cardboard cut out of it looks nice. Just need them fundage now.

Putter · 12-16-2005, 10:41 AM

I have
Tach & Speedo
Water Temp
Fuel, vacuum, volts, oil pressure

Green cab is the original one
Orange cab is the replacement

**Yukon Jack** · 12-16-2005, 10:54 AM

Here is the way I have my Autometer gauges set up.

The tach and speed positions are now reversed. Same with the clock and temp guage.

Putter · 12-16-2005, 12:23 PM

Yukon, that clock is sweet! And only 1.1 mile??? Bet it has more than that now?!?!?!

**Yukon Jack** · 12-16-2005, 01:57 PM

Quote:

Originally Posted by Putter

Yukon, that clock is sweet! And only 1.1 mile??? Bet it has more than that now?!?!?!

Nope, haven't hooked up the speedo yet

I'm still considering taking the manual speedo out and replacing it with an electronic speedo.

Putter · 12-16-2005, 02:10 PM

I love my electric one. I have recalibrated it (rear end swap) and the calibration took all of 5 minutes. Awesome.

Aquivarious · 12-16-2005, 02:13 PM

Is there a thread on here already on HOW to convert your stock to Autometer? Kinda wanna know how much work itll take so i can choose between that and getting the kits that dont look the same...

Putter · 12-16-2005, 02:22 PM

Yep....please stand by....

Here you go...LINK THINGY

Mudder · 12-16-2005, 02:28 PM

There's a couple of ways of doing it. Like Putter behind the Bezel or like mine that are put in through the front. Going in from the front is no big deal. Just use a dremel and make the bottom holes a tad bigger and drop them all in. The wiring is what took a little time. I have all electric guages except for the speedo.

**FRENCHBLUE72** · 12-17-2005, 05:14 PM

Thanks For The Link Putter That Was Gonna Be My Next Question....

12-15-2005, 09:50 PM	#1
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,601	Autometer guage bezels guys.. What autometer guages do you guys run-oil pressure- water temp-volts-tach and speedo.. What do you guys run in the other two holes???? __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

12-15-2005, 10:12 PM	#2
rocknss Registered User Join Date: Oct 2004 Location: Milwaukee, WI Posts: 403	Re: Autometer guage bezels guys.. I use a Brothers billet dash bezel with Autometer Phantom guages.

12-15-2005, 10:23 PM	#3
71swb4x4 Senior Member Join Date: Nov 2003 Location: Brookings, SD Posts: 10,497	Re: Autometer guage bezels guys.. Fuel gauge would be a good one. My last one is tranny temp. __________________ Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs.

12-15-2005, 11:09 PM	#4
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,601	Re: Autometer guage bezels guys.. Ya I guess that a fuel guage would be a good idea.. That would be the one for the center hole correct??? But hard to find also?? __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

12-16-2005, 10:41 AM	#6
Putter More Cowbell.... Join Date: Mar 2004 Location: Puckett, MS Posts: 3,569	Re: Autometer guage bezels guys.. I have Tach & Speedo Water Temp Fuel, vacuum, volts, oil pressure Green cab is the original one Orange cab is the replacement Attached Images __________________ *There once was a member from Puckett.....Who ( fill in the blank blank blank* ) bucket** Last edited by Putter; 12-16-2005 at 12:22 PM.

12-16-2005, 10:54 AM	#7
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	Re: Autometer guage bezels guys.. Here is the way I have my Autometer gauges set up. The tach and speed positions are now reversed. Same with the clock and temp guage. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 Last edited by Yukon Jack; 12-16-2005 at 10:55 AM.

12-16-2005, 12:23 PM	#8
Putter More Cowbell.... Join Date: Mar 2004 Location: Puckett, MS Posts: 3,569	Re: Autometer guage bezels guys.. Yukon, that clock is sweet! And only 1.1 mile??? Bet it has more than that now?!?!?! __________________ *There once was a member from Puckett.....Who ( fill in the blank blank blank* ) bucket**

12-16-2005, 02:10 PM	#10
Putter More Cowbell.... Join Date: Mar 2004 Location: Puckett, MS Posts: 3,569	Re: Autometer guage bezels guys.. I love my electric one. I have recalibrated it (rear end swap) and the calibration took all of 5 minutes. Awesome. __________________ *There once was a member from Puckett.....Who ( fill in the blank blank blank* ) bucket**

12-16-2005, 02:13 PM	#11
Aquivarious Registered User Join Date: Sep 2005 Location: Alton, Illinois Posts: 90	Re: Autometer guage bezels guys.. Is there a thread on here already on HOW to convert your stock to Autometer? Kinda wanna know how much work itll take so i can choose between that and getting the kits that dont look the same... __________________ '71 Chevy C-10 SWB (Project) '04 Mazda RX-8 (F*** around Car) '85 Chevy C-20 (Former Project) Currently Serving In IRAQ. (Man it sucks over here..)

12-16-2005, 02:22 PM	#12
Putter More Cowbell.... Join Date: Mar 2004 Location: Puckett, MS Posts: 3,569	Re: Autometer guage bezels guys.. Yep....please stand by.... Here you go...LINK THINGY __________________ *There once was a member from Puckett.....Who ( fill in the blank blank blank* ) bucket** Last edited by Putter; 12-16-2005 at 02:24 PM.

12-16-2005, 02:28 PM	#13
Mudder Registered User Join Date: Feb 2001 Location: East Central, MO Posts: 11,336	Re: Autometer guage bezels guys.. There's a couple of ways of doing it. Like Putter behind the Bezel or like mine that are put in through the front. Going in from the front is no big deal. Just use a dremel and make the bottom holes a tad bigger and drop them all in. The wiring is what took a little time. I have all electric guages except for the speedo. Attached Images

12-17-2005, 05:14 PM	#14
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,601	Re: Autometer guage bezels guys.. Thanks For The Link Putter That Was Gonna Be My Next Question.... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.