Need help with these bolts!! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Nima** · 03-26-2006, 10:34 AM

Well, last night I started the front disc swap finally. Everything was going well on disassembly section until I got to these bolts. Oh man, for the life of me I could't move them. I thought there migt be load or something on them but I didn't see anything therefore I soaked them with penetrating oil. This morning I tried again, NOTHING!. Any ideas? Heat, Hammer, ....

jakeslim · 03-26-2006, 11:07 AM

not related to these bolts, but in general stubborn bolts can be taken off with a drive impact tool(manual). I picked up one of these to remove a rotor(honda).You put the socket on and hit it with a big hammer, applies up to 200ft lbs of torque to break bolts loose

You may want to pick one up. I got mine at NAPA auto

cdowns · 03-26-2006, 11:22 AM

i'd spray penatrating (pb blaster)stuff from the backside for a couple of days then apply gentle heat to try and loosen them up// you have to take care about applying too much force(impact tools and long breaker bar extensions) especially on the smaller bottom bolts because it is very easy to break them off in the spindles

CG · 03-26-2006, 11:27 AM

my brother had the same problem with his. he ended up using pb, heat and air wrench. here is the thread with peoples suggestions.

http://67-72chevytrucks.com/vboard/s...d.php?t=154613

**Nima** · 03-26-2006, 11:30 AM

Thanks guys.

Bob Moore · 03-26-2006, 02:24 PM

Nima - I don't know your complete plan but why are you disassembling at that location? If you are converting to disc brake don't you need a different spindle? I would remove the spindle at the ball joint location and not worry about the backing plate. Does your set-up use the original spindle?

Please don't flame me for asking - I'm just trying to learn.

**Nima** · 03-26-2006, 05:18 PM

No, I am putting a new spindles as well. Actually that was what I thought this morning. Then I guess I should take the whole thing off at the ball joints.

jay-dawg · 03-26-2006, 07:07 PM

i agree. just take off the drum spindle at the ball joints and put in the disc brake spindles.

Tx Firefighter · 03-26-2006, 07:26 PM

I completely agree, I usually just remove the whole spindle and pop it into the scrap pile. That saves making multiple trips with the seperate pieces.

As a side note though, if I remember correctly, those bottom 2 bolts go all the way through and have nuts on the back . No biggie if they were to break off.

72armyswbtruck · 03-26-2006, 08:04 PM

Heres a neat trick that I have used before, HOT WAX, yah yah don't laugh, take a long candle or even a birthday candle, heat it up so the wax is melting and then let the wax melt into the threads, then the wax hardens in the threads acting as a natural penetrating/lubricating oil that doesn't leak out, has worked wonders for me before, especially since I didn't have a torch

jay-dawg · 03-26-2006, 09:31 PM

Quote:

Originally Posted by 72armyswbtruck

Heres a neat trick that I have used before, HOT WAX, yah yah don't laugh, take a long candle or even a birthday candle, heat it up so the wax is melting and then let the wax melt into the threads, then the wax hardens in the threads acting as a natural penetrating/lubricating oil that doesn't leak out, has worked wonders for me before, especially since I didn't have a torch

hmm...better stick that in my file. thanks for the tip.

jay

03-26-2006, 10:34 AM	#1
Nima Blue 67 Join Date: Apr 2004 Location: Western WA Posts: 1,178	Need help with these bolts!! Well, last night I started the front disc swap finally. Everything was going well on disassembly section until I got to these bolts. Oh man, for the life of me I could't move them. I thought there migt be load or something on them but I didn't see anything therefore I soaked them with penetrating oil. This morning I tried again, NOTHING!. Any ideas? Heat, Hammer, .... Attached Images __________________ 1953 GMC 3/4 ton: current project 1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake 1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!! 1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive 1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project 2005 Silverado 2500, 4x4 Duramax, original owner

03-26-2006, 11:07 AM	#2
jakeslim Premium Level Member Join Date: Aug 2004 Location: Northern CA Posts: 829	Re: Need help with these bolts!! not related to these bolts, but in general stubborn bolts can be taken off with a drive impact tool(manual). I picked up one of these to remove a rotor(honda).You put the socket on and hit it with a big hammer, applies up to 200ft lbs of torque to break bolts loose You may want to pick one up. I got mine at NAPA auto __________________ 69 K5 CST stock- 350, 4speed 77 K5 - 383, auto, 6" lift, D60 front, 14b rear, 39" tsl's, Last edited by jakeslim; 03-26-2006 at 11:08 AM.

03-26-2006, 11:22 AM	#3
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Need help with these bolts!! i'd spray penatrating (pb blaster)stuff from the backside for a couple of days then apply gentle heat to try and loosen them up// you have to take care about applying too much force(impact tools and long breaker bar extensions) especially on the smaller bottom bolts because it is very easy to break them off in the spindles __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

03-26-2006, 11:27 AM	#4
CG BlahBlahBlah Join Date: Feb 2002 Location: Wa. Posts: 19,846	Re: Need help with these bolts!! my brother had the same problem with his. he ended up using pb, heat and air wrench. here is the thread with peoples suggestions. http://67-72chevytrucks.com/vboard/s...d.php?t=154613

03-26-2006, 11:30 AM	#5
Nima Blue 67 Join Date: Apr 2004 Location: Western WA Posts: 1,178	Re: Need help with these bolts!! Thanks guys. __________________ 1953 GMC 3/4 ton: current project 1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake 1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!! 1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive 1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project 2005 Silverado 2500, 4x4 Duramax, original owner

03-26-2006, 02:24 PM	#6
Bob Moore Registered User Join Date: Feb 2004 Location: Tacoma WA Posts: 1,365	Re: Need help with these bolts!! Nima - I don't know your complete plan but why are you disassembling at that location? If you are converting to disc brake don't you need a different spindle? I would remove the spindle at the ball joint location and not worry about the backing plate. Does your set-up use the original spindle? Please don't flame me for asking - I'm just trying to learn. __________________ 67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow

03-26-2006, 05:18 PM	#7
Nima Blue 67 Join Date: Apr 2004 Location: Western WA Posts: 1,178	Re: Need help with these bolts!! No, I am putting a new spindles as well. Actually that was what I thought this morning. Then I guess I should take the whole thing off at the ball joints. __________________ 1953 GMC 3/4 ton: current project 1967 C20: 5.3 voretc with T5 conversion, 4 wheel 8 lug disc brake 1972 Nova: my 4 door sport sedan! 5.3 voretc + T5 conversion. drivable project, FUN!! 1979 Camaro Z28: 5.3 vortec conversion with build TH350: drivable project, Fun to drive 1992 Camaro RS convertible (Z28 clone): 5.3 conversion with build T5: on going project 2005 Silverado 2500, 4x4 Duramax, original owner

03-26-2006, 07:07 PM	#8
jay-dawg chevelito Join Date: Jun 2001 Location: Honolulu, HI USA Posts: 1,609	Re: Need help with these bolts!! i agree. just take off the drum spindle at the ball joints and put in the disc brake spindles. __________________ New deadline...when my son can drive. Aloha from Honolulu, HI

03-26-2006, 07:26 PM	#9
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: Need help with these bolts!! I completely agree, I usually just remove the whole spindle and pop it into the scrap pile. That saves making multiple trips with the seperate pieces. As a side note though, if I remember correctly, those bottom 2 bolts go all the way through and have nuts on the back . No biggie if they were to break off. __________________ I'm on the Instagram- @Gearhead_Kevin

03-26-2006, 08:04 PM	#10
72armyswbtruck Registered User Join Date: Feb 2004 Location: Idaho Posts: 4,034	Re: Need help with these bolts!! Heres a neat trick that I have used before, HOT WAX, yah yah don't laugh, take a long candle or even a birthday candle, heat it up so the wax is melting and then let the wax melt into the threads, then the wax hardens in the threads acting as a natural penetrating/lubricating oil that doesn't leak out, has worked wonders for me before, especially since I didn't have a torch __________________ "Remember, They can Kill You, but they can't eat You, That's against the law!!!!!!!!!"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.