|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
04-11-2006, 11:39 AM
|
#1 |
|
Registered User
Join Date: Apr 2006
Location: Oregon
Posts: 14
|
1969 or 1970 Chevy Panel
Well I believe I found a 1969 or 1970 Chevy Panel. Some one converted it to 4 wheel drive, however the rear is still the truck arm set up while they changed the front to leaf springs. I was wondering about the front control arms if their mounts could either be unbolted from the frame or not and if they could have been then where I mount replacements to convert it back to 2 wheel drive. Also what should I look for on these things to see if it is in good enough condition to get?
|
|
|
|
04-11-2006, 10:44 PM
|
#2 |
|
Senior Member
Join Date: May 2002
Location: hamilton,ohio,usa
Posts: 1,499
|
Re: 1969 or 1970 Chevy Panel
it's a panel truck...................buy it!
they are rare as Hen's testicles. Last edited by big blue 72; 04-11-2006 at 10:45 PM. |
|
|
|
|
04-11-2006, 11:06 PM
|
#3 |
|
Registered User
Join Date: Apr 2006
Location: Oregon
Posts: 14
|
Re: 1969 or 1970 Chevy Panel
well I need to figure out how much work it will take to change it back to 2 wheel drive because I don't think it is safe as it is currently setup
|
|
|
|
|
04-12-2006, 03:12 AM
|
#4 |
|
Designated A-hole!
Join Date: Mar 2003
Location: South Mississippi
Posts: 36,450
|
Re: 1969 or 1970 Chevy Panel
The front suspension is all bolted to the front crossmember which bolts to the frame. So all you should have to do is remove the 4x crossmember and bolt a 2wd crossmember with suspension under it. In fact if you're wanting to do the disc brake conversion use the crossmember from a 71-87 truck/blazer/burb and you should be good to go.
__________________
"If it ain't broke, fix it 'til it is!" Being stupid ain't illegal.  We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck" |
|
|
|
|
04-12-2006, 03:12 AM
|
#5 |
|
Designated A-hole!
Join Date: Mar 2003
Location: South Mississippi
Posts: 36,450
|
Re: 1969 or 1970 Chevy Panel
BTW Welcome to the board from South Mississippi!
__________________
"If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck" |
|
|
|
|
04-12-2006, 01:45 PM
|
#6 |
|
Registered User
Join Date: Apr 2006
Location: Oregon
Posts: 14
|
Re: 1969 or 1970 Chevy Panel
Well it doesn't appear to have a 4x4 crossmember on it. The front of the leaf springs are attached to what appears to be a piece of plate steel that is about 1/2 inch think by about 4 inches wide that spans the width of the front frame horns. The rear is lifted by what appears to be helper springs clamped to the truck arms. Also there is no engine in the engine bay or transmission the emblems on the side of the front fender says it has or had a 396 in in. It also was an automatic at one point in time
|
|
|
|
|
04-12-2006, 10:55 PM
|
#7 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,862
|
Re: 1969 or 1970 Chevy Panel
Can you get pictures?
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
04-12-2006, 11:51 PM
|
#8 |
|
Senior Member
Join Date: Dec 2004
Location: Southern Pines NC
Posts: 3,853
|
Re: 1969 or 1970 Chevy Panel
Buy it............
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
