![]() |
![]() |
#1 |
Registered User
Join Date: Apr 2006
Location: nc
Posts: 10
|
![]()
hey yall i am new to the board.i have a 1967 chevy c10 long bed, it has a 250 inliner with a factory 3 speed tranny, im putting a 327 in it where could i find a v8 bellhousing for this tranny. i have looked in all the junkyards and tried all of my connections and no luck finding one. i didnt think it would be this hard finding one, maybe nobody wants to sell em idk?? thanks in advance for any advice
Last edited by 67greenmachine; 07-30-2006 at 05:36 PM. |
![]() |
![]() |
![]() |
#2 |
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,403
|
Re: bellhousing swap
No need to swap....the I6 bell will bolt right on the 327. You can also use the flywheel/clutch/pressure plate, but it will be a 10 1/2" setup, vs the 11" V8 pcs.......
![]()
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Apr 2006
Location: nc
Posts: 10
|
Re: bellhousing swap
ok i was just wondering cause iv always messed with v8's never fooled with a inliner so thanks for the advice..
|
![]() |
![]() |
![]() |
#4 |
RIP Mr Ron
![]() Join Date: Dec 2005
Location: Big Sandy, Tn. 38221
Posts: 8,166
|
Re: bellhousing swap
I think you can use the one you got. It should be the same.
__________________
Ron (Mr Round Tuit) ![]() Be kinder than necessary, for everyone you meet is fighting some kind of battle TN Message Forum TN Facebook Group SETN Truck Show My Photobucket |
![]() |
![]() |
![]() |
#5 |
RIP Mr Ron
![]() Join Date: Dec 2005
Location: Big Sandy, Tn. 38221
Posts: 8,166
|
Re: bellhousing swap
O yeah welcome to the board from West Tennessee. Good luck with your engine swap.
__________________
Ron (Mr Round Tuit) ![]() Be kinder than necessary, for everyone you meet is fighting some kind of battle TN Message Forum TN Facebook Group SETN Truck Show My Photobucket |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Apr 2006
Location: nc
Posts: 10
|
Re: bellhousing swap
appreciate it!!
|
![]() |
![]() |
![]() |
#7 |
Senior Moment
![]() Join Date: Mar 2002
Location: Pittsburg Ca
Posts: 4,133
|
Re: bellhousing swap
The clutch Z bar will be differant for the V8
__________________
1970 CST LS 1 6 speed Ford 9 inch Detroit Tru Track, Dakota Didgital, Vintage Air, QA1 Coil Overs Front & Rear Lots of FUN 2013 GMC PU, Oldest Son 71 GMC LWB. QA1 Suspension, Angry SB. Youngest Son 2019 GMC Diesil Dually. Youngest Son 2017 Toyota SUV Daughters car 2018 Traverse , Wife’s Ride Pittsburg Ca 94565 |
![]() |
![]() |
![]() |
Bookmarks |
|
|