Front Roll Pan Install Help!! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

whatnow123 · 08-06-2007, 01:15 PM

Hey Everyone,

I bought a front roll pan for the 67. Looks to be a well made piece and I bought it from Mar-K. Anyway when I received the roll pan, I laid it on top of the grill (the grill was upside down as it's not currently on the truck) to test fit it and to determine the best way to install this piece. While doing that, I noticed that the curve along the length of the roll pan is off compared to the grill piece it attaches to. So, I lined up one end of it flush to the grill and it seems to be off by well over an inch on the other side. My first thought is that the grill was bent, but that isn't the case as it lines up perfectly with the fenders and there is no sign at all of it ever being damaged. The roll pan doesn't appear to be damaged in any way during shipping either.

Is the roll pan made wrong or is there a trick to installing these?

Thanks!

cdowns · 08-06-2007, 02:08 PM

you need to trim a piece off the front of each framerail for starters on most of the pans i've seen

PanelDeland · 08-06-2007, 04:17 PM

Try centering everything.There is probably some excess on each end of the roll pan so you can trim it to fit when you mold it in.

whatnow123 · 08-06-2007, 05:21 PM

Here is some photos of what I'm talking about. It looks simple enough to "pull" the rollpan over but it's actually a very well built piece of metal and if I try to change the curvature of it, nothing good is going to come of it. I have Mar-k checking it as well. To be honest, I'm not sure what I'm going to do if they say nothing is wrong, as I have already cut the horns a while ago knowing I'm going with a roll pan. My grill is in really good shape (considering it's 40 years old) and has no signs at all of any type of major damage.

My thoughts are it's made wrong and it shouldn't be this far out of whack. Anyone installed one of these? Advise?

MAR-Ktech · 08-07-2007, 05:15 PM

We replied directly to this customer, but wanted to pass the information along to anyone who might be interested in our front pan.
Here is part of the email we sent:
"Do you happen to have the baffle panel (or the splash panel) that goes
between the grille and the radiator core support? This piece will
establish the exact curve of the grille when they are bolted together.
If the grille is bent, then the baffle panel will not fit match the
shape of the grille.
We make our front pan to exactly match that baffle panel. The
recommended installation is that you would slide the front pan flange
between the grille and the baffle panel. When you push it all the way
in, the curve of the pan should match the curve of the baffle panel and
grille. Then you bolt the baffle panel to the grille with the flange
in between."

We also faxed him a copy of the assembly manual that shows the grille and baffle together.

Complete instructions for the front pan are available here:
http://www.mar-k.com/GM_67-72_Front_Pan.pdf

Hope this helps!

jb4short · 08-07-2007, 05:30 PM

Nice...I think I want one of those- it's sharp!

brossow · 10-15-2007, 10:16 PM

Not to revive a dead thread, but I'm wondering how this ever turned out. Considering a front rollpan for my '72 and want to avoid problems.

whatnow123 · 10-15-2007, 10:52 PM

Turned out fine. The grill was a little out of whack, but it looks great now. Click on my build thread, there is a photo of it mounted.

brossow · 10-15-2007, 11:37 PM

Looks great! Overlooked the pan earlier today when I was skimming through your build thread instead of doing real work. Thanks for the pointer.

08-06-2007, 01:15 PM	#1
whatnow123 Registered User Join Date: Oct 2006 Location: Arizona Posts: 835	Front Roll Pan Install Help!! Hey Everyone, I bought a front roll pan for the 67. Looks to be a well made piece and I bought it from Mar-K. Anyway when I received the roll pan, I laid it on top of the grill (the grill was upside down as it's not currently on the truck) to test fit it and to determine the best way to install this piece. While doing that, I noticed that the curve along the length of the roll pan is off compared to the grill piece it attaches to. So, I lined up one end of it flush to the grill and it seems to be off by well over an inch on the other side. My first thought is that the grill was bent, but that isn't the case as it lines up perfectly with the fenders and there is no sign at all of it ever being damaged. The roll pan doesn't appear to be damaged in any way during shipping either. Is the roll pan made wrong or is there a trick to installing these? Thanks! __________________ 67 Short Step, 355, 700R 4.11 posi rear, 4/6 drop Discs on all 4 corners. Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=219094

08-06-2007, 02:08 PM	#2
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: Front Roll Pan Install Help!! you need to trim a piece off the front of each framerail for starters on most of the pans i've seen __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

08-06-2007, 04:17 PM	#3
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,993	Re: Front Roll Pan Install Help!! Try centering everything.There is probably some excess on each end of the roll pan so you can trim it to fit when you mold it in. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" Last edited by PanelDeland; 08-06-2007 at 04:18 PM.

08-06-2007, 05:21 PM	#4
whatnow123 Registered User Join Date: Oct 2006 Location: Arizona Posts: 835	Re: Front Roll Pan Install Help!! Here is some photos of what I'm talking about. It looks simple enough to "pull" the rollpan over but it's actually a very well built piece of metal and if I try to change the curvature of it, nothing good is going to come of it. I have Mar-k checking it as well. To be honest, I'm not sure what I'm going to do if they say nothing is wrong, as I have already cut the horns a while ago knowing I'm going with a roll pan. My grill is in really good shape (considering it's 40 years old) and has no signs at all of any type of major damage. My thoughts are it's made wrong and it shouldn't be this far out of whack. Anyone installed one of these? Advise? Attached Images __________________ 67 Short Step, 355, 700R 4.11 posi rear, 4/6 drop Discs on all 4 corners. Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=219094

08-07-2007, 05:15 PM	#5
MAR-Ktech Truck Parts Mfg. Join Date: Jul 2005 Location: Oklahoma City, OK Posts: 697	Re: Front Roll Pan Install Help!! We replied directly to this customer, but wanted to pass the information along to anyone who might be interested in our front pan. Here is part of the email we sent: "Do you happen to have the baffle panel (or the splash panel) that goes between the grille and the radiator core support? This piece will establish the exact curve of the grille when they are bolted together. If the grille is bent, then the baffle panel will not fit match the shape of the grille. We make our front pan to exactly match that baffle panel. The recommended installation is that you would slide the front pan flange between the grille and the baffle panel. When you push it all the way in, the curve of the pan should match the curve of the baffle panel and grille. Then you bolt the baffle panel to the grille with the flange in between." We also faxed him a copy of the assembly manual that shows the grille and baffle together. Complete instructions for the front pan are available here: http://www.mar-k.com/GM_67-72_Front_Pan.pdf Hope this helps! __________________ GET MAR-K Quality! Restoration and Custom Pickup Parts for Chevy, GMC, Ford, Dodge and Custom Trucks Last edited by MAR-Ktech; 08-07-2007 at 05:17 PM.

08-07-2007, 05:30 PM	#6
jb4short Damn Yankee Join Date: Feb 2007 Location: Lynchburg, VA Posts: 2,261	Re: Front Roll Pan Install Help!! Nice...I think I want one of those- it's sharp!

10-15-2007, 10:16 PM	#7
brossow Amateur Rust Fighter Join Date: Sep 2007 Location: Mankato, MN Posts: 1,087	Re: Front Roll Pan Install Help!! Not to revive a dead thread, but I'm wondering how this ever turned out. Considering a front rollpan for my '72 and want to avoid problems. __________________ Brent '72 Chevy SWB stepside - [ Build Thread ] '79 ChevMC SWB fleetside - [ Build Thread ] '64 Chevy SWB fleetside & '66 Chevy SWB stepside (waiting in the wings...)

10-15-2007, 10:52 PM	#8
whatnow123 Registered User Join Date: Oct 2006 Location: Arizona Posts: 835	Re: Front Roll Pan Install Help!! Turned out fine. The grill was a little out of whack, but it looks great now. Click on my build thread, there is a photo of it mounted. __________________ 67 Short Step, 355, 700R 4.11 posi rear, 4/6 drop Discs on all 4 corners. Build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=219094

10-15-2007, 11:37 PM	#9
brossow Amateur Rust Fighter Join Date: Sep 2007 Location: Mankato, MN Posts: 1,087	Re: Front Roll Pan Install Help!! Looks great! Overlooked the pan earlier today when I was skimming through your build thread instead of doing real work. Thanks for the pointer. __________________ Brent '72 Chevy SWB stepside - [ Build Thread ] '79 ChevMC SWB fleetside - [ Build Thread ] '64 Chevy SWB fleetside & '66 Chevy SWB stepside (waiting in the wings...)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.