Floor Shift from Van Tilt? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**special-K** · 01-08-2008, 05:28 AM

What does it take to make a 4spd floor shift tilt column from a column shift tilt?

**jerry moss** · 01-08-2008, 06:05 AM

Tim,
i got the pieces necessary from an older GM car tilt with a floor shift--the cup where the shift handle was and the upper tin cover. i got lucky finding those pieces but a little JB Weld should fix the shift handle issue and the upper cover is tin so welding/brazing/soldering should be no problem. hope this helps.
by the way, i didn't destroy a good column to get the pieces i used, it was already butchered up.

corn · 01-08-2008, 09:20 AM

I JB welded my van auto column for a floor shift. Should be about the same thing...

**Yukon Jack** · 01-09-2008, 09:19 AM

Here's a link showing my conversion for my K20. JB weld and I used some cut out pieces from a beer can to help fill in the large areas with JB on top. Sands down real nice.

corn · 01-09-2008, 01:41 PM

Quote:

Originally Posted by Yukon Jack

Here's a link showing my conversion for my K20. JB weld and I used some cut out pieces from a beer can to help fill in the large areas with JB on top. Sands down real nice.

Haha, that sounds familiar but I used a DEW can...

01-08-2008, 05:28 AM	#1
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,861	Floor Shift from Van Tilt? What does it take to make a 4spd floor shift tilt column from a column shift tilt? __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

01-08-2008, 06:05 AM	#2
jerry moss Born Psycho Join Date: Feb 2001 Location: brentwood,cal,usa Posts: 4,861	Re: Floor Shift from Van Tilt? Tim, i got the pieces necessary from an older GM car tilt with a floor shift--the cup where the shift handle was and the upper tin cover. i got lucky finding those pieces but a little JB Weld should fix the shift handle issue and the upper cover is tin so welding/brazing/soldering should be no problem. hope this helps. by the way, i didn't destroy a good column to get the pieces i used, it was already butchered up. __________________ jerry moss 72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD 69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies. 73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog. 77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW BRENTWOOD,CALIFORNIA

01-08-2008, 09:20 AM	#3
corn Registered User Join Date: Dec 2003 Location: here Posts: 5,789	Re: Floor Shift from Van Tilt? I JB welded my van auto column for a floor shift. Should be about the same thing...

01-09-2008, 09:19 AM	#4
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,684	Re: Floor Shift from Van Tilt? Here's a link showing my conversion for my K20. JB weld and I used some cut out pieces from a beer can to help fill in the large areas with JB on top. Sands down real nice. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.