The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > Info Center > FAQ Truck Tech > Engine and Drivetrain

Web 67-72chevytrucks.com


 
 
Thread Tools Display Modes
Old 01-24-2009, 05:48 PM   #1
GMCMAX
Active Member
 
GMCMAX's Avatar
 
Join Date: Jan 2006
Location: Lower Mid-East Ca.
Posts: 326
Alternator bearing how-to

Had the front alternator bearing on the 66 El Camino start making noise, took it apart and lubed it, wasn't thinking when I started, but took pix going back together. This is easy to do, either lube or replace bearing, if it charges it's lots cheaper to repair.
OK, alternator- Remove pulley, fan and spacer, use impact, or loosen nut when on engine so you can use the belt to hold it.


Remove 4 bolts from perimeter, make sure to mark case halves to get them back rotated right (paper tag was my mark). Slide off front cover while leaving windings in lower half. Keep the shaft (rotor) in the bottom half also so it doesn't pop up and down and break a brush.

Pull the rotor out and remove the three screws holding the front bearing in, then tap the bearing out.

Carefully pop the cover off the bearing. Inspect and either replace or lube with fresh grease.

A little grease on the rear bearing, and the trick- Use a non-metallic item such as a toothpick or spray can straw from the backside to retain the brushes for re-assembly.



Put it all back together, remove your toothpick, back on car, and run.

Nice and quiet now..
Max
__________________
Never try to teach a pig to sing; it wastes your time and annoys the pig!

Gets More Chicks

My lugnuts require more torque than your honda makes!

68 GMC, 4X4 conversion w/73 k20 running gear and springs, 350 4spd, 4.10's, D44 powerlok front, 14BFF govlock rear, 33" tires, lifted 4".

Last edited by augie; 04-04-2011 at 12:59 AM.
GMCMAX is offline  
Old 01-24-2009, 08:34 PM   #2
oldblue1968chevy
Grandpa in the rustmobile...
 
oldblue1968chevy's Avatar
 
Join Date: Nov 2008
Location: Spokane WA/Viola TN
Posts: 11,422
Re: Alternator bearing how-to

GREAT WRITE UP!!!

Thanks a ton..my bearing in my alt. is startin to go out....this needs to be a sticky or something lol!

thanks! good job!
__________________
John

Goose-1968 C10 355,9.32-1CR, Vortec Heads ,262 voodoo, 3.73:1 3OTT (HS ride/beater/farm truck)
http://67-72chevytrucks.com/vboard/s...d.php?t=317684

Grams 53-1953 Chevrolet Belair
http://67-72chevytrucks.com/vboard/s...=1#post4327784

1969 Chevy C10 Shortbed 4.5/6?" Frame off resto
http://67-72chevytrucks.com/vboard/s...d.php?t=548136

1999 Toyota Tacoma 4x4
oldblue1968chevy is offline  
 

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:41 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com