67 C/10 BBC mounts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bigblocksean · 02-28-2010, 01:18 AM

Greetings all, I have a question on placement of a BBC into the 67 C/10 the frame mounts were for a sbc, does the bbc need to be set back farther, thank you

**too much stuff** · 02-28-2010, 01:48 AM

You will probably want to use a set of big block towers in the front set of holes in the frame. I am not positive on the 67 frame being the same as later as far as location, but i am pretty sure...

Jacfourteen · 02-28-2010, 02:18 AM

I'm no expert on this but I recall that the hole placement is right (front set). but the frame is too narrow, so you need to grind about 1/4" off each side to make them fit. I'm sure someone has more expertise though.

bigblocksean · 02-28-2010, 07:11 PM

Thanks guys! wow those factory big block mounts are spendy, problem solved I fabbed up a set that is going to work great.

02-28-2010, 01:18 AM	#1
bigblocksean Registered User Join Date: Feb 2010 Location: Arkansas City, Kansas Posts: 33	67 C/10 BBC mounts Greetings all, I have a question on placement of a BBC into the 67 C/10 the frame mounts were for a sbc, does the bbc need to be set back farther, thank you

02-28-2010, 01:48 AM	#2
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,717	Re: 67 C/10 BBC mounts You will probably want to use a set of big block towers in the front set of holes in the frame. I am not positive on the 67 frame being the same as later as far as location, but i am pretty sure... __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

02-28-2010, 02:18 AM	#3
Jacfourteen Big Red - Now its a SWB! Join Date: Jun 2009 Location: Oroville, Ca Posts: 1,624	Re: 67 C/10 BBC mounts I'm no expert on this but I recall that the hole placement is right (front set). but the frame is too narrow, so you need to grind about 1/4" off each side to make them fit. I'm sure someone has more expertise though. __________________ 68 3/4 ton (Project)-350 Small Block, .030 over, 10:1 comp, 3998993 heads, C3BX edelbrock intake, comp cams XE268, Holley 670 SA, long tube headers, dual flow 40's, E-fan, Alum rad, currently under the knife getting shortened and bagged build thread 41 3/4 ton (wife's)-flatbed, fully restored to original 01 Tahoe LT 4WD (my daily driver)-Magnaflow Muffler, Rollin on 22's 02 Ford Mustang Convertable (Wife's Car)-Flowmaster 50, Clear corners, Intake, sittin on 18's

02-28-2010, 07:11 PM	#4
bigblocksean Registered User Join Date: Feb 2010 Location: Arkansas City, Kansas Posts: 33	Re: 67 C/10 BBC mounts Thanks guys! wow those factory big block mounts are spendy, problem solved I fabbed up a set that is going to work great.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.