lay pinch or rocker on PB dropmember - The 1947 - Present Chevrolet & GMC Truck Message Board Network

altereddezignz · 03-29-2010, 09:10 PM

Hey guys i am gonna order a pb dropmember from Nate tomorow. I was curious what all you guys are running to lay pinch or rocker. i wouls liek to run 22 front and rear about a 28-29 tall tire, maybe a 20 front and 24 rear. Looks like ill be using tubular upp and lower control arms.

Thanks for the help

flamingbig10 · 03-29-2010, 09:21 PM

the frame hangs lower than the body so you'll be a couple inches away from laying pinch

altereddezignz · 03-29-2010, 09:22 PM

oh i have already planned on cutting that all off and boxing it in under the cab.

crawdadfox · 03-30-2010, 09:53 PM

With Dropmembers and 3" spindles on the old truck and the frame planted on the ground there was 1 1/4" to the pinch weld. With the truck on our drive on rack aired out i had an extra 1 1/4" of drop below "ground zero"...so if you did cut the same amount off the bottom of the frame (i wouldn't) you would lay pinch. I was on a 29.1" front and 29.9 rear tire, if you ran a shorter tire you would be lower....but do you need to be?

altereddezignz · 03-30-2010, 10:02 PM

Weill I have decieded to use 4x2 and build new rails from just n front of the cab to the rearend. This way I'm nit cutting and reducing the integrity and strength of the frame.

03-29-2010, 09:10 PM	#1
altereddezignz Registered User Join Date: Feb 2010 Location: jonesboro arkansas Posts: 104	lay pinch or rocker on PB dropmember Hey guys i am gonna order a pb dropmember from Nate tomorow. I was curious what all you guys are running to lay pinch or rocker. i wouls liek to run 22 front and rear about a 28-29 tall tire, maybe a 20 front and 24 rear. Looks like ill be using tubular upp and lower control arms. Thanks for the help

03-29-2010, 09:21 PM	#2
flamingbig10 6.0 powered square Join Date: Feb 2008 Location: Mesquite texas Posts: 3,459	Re: lay pinch or rocker on PB dropmember the frame hangs lower than the body so you'll be a couple inches away from laying pinch __________________ Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326

03-29-2010, 09:22 PM	#3
altereddezignz Registered User Join Date: Feb 2010 Location: jonesboro arkansas Posts: 104	Re: lay pinch or rocker on PB dropmember oh i have already planned on cutting that all off and boxing it in under the cab.

03-30-2010, 09:53 PM	#4
crawdadfox Registered User Join Date: Aug 2008 Location: New Orleans Louisiana.....a great place to visit but you wouldn't want to live here!!! Posts: 883	Re: lay pinch or rocker on PB dropmember With Dropmembers and 3" spindles on the old truck and the frame planted on the ground there was 1 1/4" to the pinch weld. With the truck on our drive on rack aired out i had an extra 1 1/4" of drop below "ground zero"...so if you did cut the same amount off the bottom of the frame (i wouldn't) you would lay pinch. I was on a 29.1" front and 29.9 rear tire, if you ran a shorter tire you would be lower....but do you need to be? Attached Images __________________ Down......with the sickness!!

03-30-2010, 10:02 PM	#5
altereddezignz Registered User Join Date: Feb 2010 Location: jonesboro arkansas Posts: 104	Re: lay pinch or rocker on PB dropmember Weill I have decieded to use 4x2 and build new rails from just n front of the cab to the rearend. This way I'm nit cutting and reducing the integrity and strength of the frame.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.